r: 02020222 p: 20.64 pid: 95044 b: FISCHER q: 0 st: lt: 8 ean: 4006209970713 sr: FISCHER 97071 sr_no_br: 97071 sr_no_br_cl: 97071 sr_cl: FISCHER97071 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 20 mm Length 210 mm Anchoring depth 210 mm Width across flats 30 mm Effective length 50 mm Drill hole depth 235 mm Drilling diameter 25 mm n: FISCHER 97071 highbond anchor FHB II-A L M20 x 210/50 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tensile loads. The fischer Highbond rod anchor FHB II-A L is produced from zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that large machines and heavy steel constructions are securely installed within internal areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M20 x 210/50 ev kpn: 97071 kpn_dash: kpn_clear: 97071 bkpn: FISCHER 97071 bkpn_clear: FISCHER 97071 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97071 sr_ns: FISCHER97071
r: 87051277 p: 20.51 pid: 74367 b: FISCHER q: 0 st: lt: 8 ean: 4006209607244 sr: FISCHER 60724 sr_no_br: 60724 sr_no_br_cl: 60724 sr_cl: FISCHER60724 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 22 mm Effective length 60 mm Overall length 184 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M16 n: FISCHER 60724 zykon anchor FZA 22 x 100 M16/60 electrolytically galvanised cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The fixing system with the highest safety in cracked concrete. The fischer ZYKON bolt anchor is an anchor made of zinc-plated steel. The special drill bit FZUB is used to create the undercut drill hole in a single work step. The undercut anchor is set in the pre-positioned installation. The expansion sleeve is driven above the cone with the setting tool FZE Plus and fills the undercut drill hole with a positive fit. The fischer ZYKON bolt anchor FZA is ideal for fixing steel constructions, railings, and machines within internal areas in cracked concrete. Maximum safety due to a positive fit connection Low axial and edge distances due to expansion pressure-free installation Fast installation, no exchanging tools. This saves time and costs Power-saving installation with low setting energy ETA approval for cracked concrete and fire resistance class R 120 The special ZYKON undercut technology allows for a positive fit connection and ensures maximum safety, even in large cracks The almost expansion-free installation of the anchor allows small edge distances and axial spacing, and thereby enables flexible use The FZUB special drill allows for a fast installation by creating the undercut without having to change tools The drill hole geometry allows for a very low setting energy, thus reducing the energy required for installation Suitable for The FZA is suitable for pre-positioned installation The undercut drill hole is created using the special FZUB drill Once the anchor has been placed in the drill hole, the expansion sleeve is driven over the cone using the FZE Plus setting tool, and the undercut drill hole is filled with a positive fit Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steelwork constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: zykon anchor FZA 22 x 100 M16/60 electrolytically galvanised kpn: 60724 kpn_dash: kpn_clear: 60724 bkpn: FISCHER 60724 bkpn_clear: FISCHER 60724 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 60724 sr_ns: FISCHER60724
r: 87051309 p: 20.51 pid: 37431 b: FISCHER q: 0 st: lt: 8 ean: 4006209607633 sr: FISCHER 60763 sr_no_br: 60763 sr_no_br_cl: 60763 sr_cl: FISCHER60763 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm n: FISCHER FZA 22x100 M12 Zykon female threaded anchor electrolytically zinc-plated - 60763 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The internally threaded anchor with the highest safety for cracked concrete. The fischer ZYKON internal threaded anchor FZA-I is an anchor made of zinc-plated steel. The special drill bit FZUB is used to create the undercut drill hole in a single work step. The undercut anchor is set in the pre-positioned installation. The expansion sleeve is driven above the cone with the setting tool FZE Plus and fills the undercut drill hole with a positive fit. The fischer ZYKON internal threaded anchor FZA-I is ideal for fixing steel constructions, ceiling installations, and consoles within internal areas in cracked concrete. Maximum safety due to a positive fit connection High flexibility due to using conventional metric screws and threaded rods Surface flush removal possible Fast installation, no exchanging tools. This saves time and costs ETA approval for cracked concrete and fire resistance class R 120 The special ZYKON undercut technology allows for a positive fit connection and ensures maximum safety, even in large cracks The metric internal thread means that it is possible to use standard screws or threaded rods for the ideal adaptation to suit the intended use The FZA-I allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility Furthermore, the ZYKON undercut anchor FZA-I offers all the benefits of the FZA Suitable for FZA-I with internal thread is suitable for pre-positioned installation The undercut drill hole is created using the special FZUB drill Once the anchor has been placed in the drill hole, the expansion sleeve is driven over the cone using the FZE Plus setting tool, and the undercut drill hole is filled with a positive fit Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates ds: dsc: kts: Zykon female threaded anchor electrolytically zinc-plated kpn: FZA 22x100 M12 kpn_dash: kpn_clear: FZA22x100M12 bkpn: FISCHER FZA 22x100 M12 bkpn_clear: FISCHER FZA22x100M12 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 60763 sr_ns: FISCHER60763
r: 02137036 p: 20.46 pid: 176196 b: FISCHER q: 0 st: lt: 8 ean: 4006209907207 sr: FISCHER 90720 sr_no_br: 90720 sr_no_br_cl: 90720 sr_cl: FISCHER90720 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 27 mm Length 340 mm n: FISCHER 90720 anchor rod RG M27 x 340 electrolytically zinc-plated 5.8 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The proven rod anchor for internal use with a mortar cartridge or injection mortar. The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5. 8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas. Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge Zinc-galvanised steel for internal use The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety Please refer to the approvals for the resin capsules and mortar used Suitable for Due to its oblique edge, the anchor rod RG M is particularly suitable for use in conjunction with resin capsules The anchor rod RG M is set using a hammer drill and the accompanying setting tool in rotating and hitting motions During setting, the oblique edge of the RG M destroys the capsule, and mixes and activates the mortar Use with injection mortar is also possible. Here, the anchor rod is manually inserted into the drill hole with a light rotating movement until it reaches the base of the hole Building materials In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete In connection with several fischer injection mortars approved or suitable for different building materials Application Anchorings with resin capsule RSB and RSB mini Anchorings with resin capsule RM II Anchorings with each of the fischer injection mortars FIS SB, FIS EM, FIS EB II, FIS V, FIS VL, FIS V Zero, FIS P Plus, FIS P, FIS EP and FIS Green ds: dsc: kts: anchor rod RG M27 x 340 electrolytically zinc-plated 5.8 kpn: 90720 kpn_dash: kpn_clear: 90720 bkpn: FISCHER 90720 bkpn_clear: FISCHER 90720 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 90720 sr_ns: FISCHER90720
r: 08096937 p: 20.29 pid: 176329 b: FISCHER q: 0 st: lt: 8 ean: 4048962462654 sr: FISCHER 564640 sr_no_br: 564640 sr_no_br_cl: 564640 sr_cl: FISCHER564640 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 10 mm Overall length 110 mm Material (bolt) Steel Surface treatment (bolt) None Thread dimension M12 n: FISCHER 564640 Piercing anchor FAZ II Plus 12/10 HCR high-corrosion steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 12/10 HCR high-corrosion steel kpn: 564640 kpn_dash: kpn_clear: 564640 bkpn: FISCHER 564640 bkpn_clear: FISCHER 564640 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564640 sr_ns: FISCHER564640
r: 87051284 p: 20.21 pid: 74391 b: FISCHER q: 0 st: lt: 8 ean: 4006209607794 sr: FISCHER 60779 sr_no_br: 60779 sr_no_br_cl: 60779 sr_cl: FISCHER60779 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 14 mm Effective length 25 mm Overall length 102 mm Material (bolt) Stainless steel A4 Thread dimension M10 n: FISCHER 60779 zykon anchor FZA 14 x 60 M10/25 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The system consists of stainless steel for optimum safety in cracked concrete. The fischer ZYKON bolt anchor FZA is an anchor made of stainless steel. The special drill bit FZUB is used to create the undercut drill hole in a single work step. The undercut anchor is set in the pre-positioned installation. The expansion sleeve is driven above the cone with the setting tool FZE Plus and fills the undercut drill hole with a positive fit. The fischer ZYKON bolt anchor FZA is ideal for fixing façades, railings, and steel constructions within external areas in cracked concrete. Maximum safety due to a positive fit connection Low axial and edge distances due to expansion pressure-free installation Fast installation, no exchanging tools. This saves time and costs Power-saving installation with low setting energy ETA approval for cracked concrete and fire resistance class R 120 The special ZYKON undercut technology allows for a positive fit connection and ensures maximum safety, even in large cracks The almost expansion-free installation of the anchor allows small edge distances and axial spacing, and thereby enables flexible use The FZUB special drill allows for a fast installation by creating the undercut without having to change tools The drill hole geometry allows for a very low setting energy, thus reducing the energy required for installation Suitable for The FZA is suitable for pre-positioned installation The undercut drill hole is created using the special FZUB drill Once the anchor has been placed in the drill hole, the expansion sleeve is driven over the cone using the FZE Plus setting tool, and the undercut drill hole is filled with a positive fit Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steelwork constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: zykon anchor FZA 14 x 60 M10/25 R stainless steel kpn: 60779 kpn_dash: kpn_clear: 60779 bkpn: FISCHER 60779 bkpn_clear: FISCHER 60779 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 60779 sr_ns: FISCHER60779
r: 87051312 p: 20.21 pid: 17537 b: FISCHER q: 0 st: lt: 8 ean: 4006209607862 sr: FISCHER 60786 sr_no_br: 60786 sr_no_br_cl: 60786 sr_cl: FISCHER60786 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 8 mm n: FISCHER FZA 14x60 M8 R Zykon female threaded anchor stainless steel - 60786 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The internally threaded anchor consists of stainless steel for optimum safety in cracked concrete. The fischer ZYKON internal threaded anchor FZA-I is an anchor made of stainless steel. The special drill bit FZUB is used to create the undercut drill hole in a single work step. The undercut anchor is set in the pre-positioned installation. The expansion sleeve is driven above the cone with the setting tool FZE Plus and fills the undercut drill hole with a positive fit. The fischer ZYKON internal threaded anchor FZA-I is ideal for fixing steel constructions, staircases, and temporary fixings within external areas in cracked concrete. Maximum safety due to a positive fit connection High flexibility due to using conventional metric screws and threaded rods Fast installation, no exchanging tools. This saves time and costs ETA approval for cracked concrete and fire resistance class R 120 Made of stainless steel for fixings used outside The special ZYKON undercut technology allows for a positive fit connection and ensures maximum safety, even in large cracks The metric internal thread means that it is possible to use standard screws or threaded rods for the ideal adaptation to suit the intended use The FZA-I allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility Furthermore, the ZYKON undercut anchor FZA-I offers all the benefits of the FZA Suitable for FZA-I with internal thread is suitable for pre-positioned installation The undercut drill hole is created using the special FZUB drill Once the anchor has been placed in the drill hole, the expansion sleeve is driven over the cone using the FZE Plus setting tool, and the undercut drill hole is filled with a positive fit Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates ds: dsc: kts: Zykon female threaded anchor stainless steel kpn: FZA 14x60 M8 R kpn_dash: kpn_clear: FZA14x60M8R bkpn: FISCHER FZA 14x60 M8 R bkpn_clear: FISCHER FZA14x60M8R c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 60786 sr_ns: FISCHER60786
r: 08096948 p: 19.45 pid: 176341 b: FISCHER q: 0 st: lt: 8 ean: 4048962462647 sr: FISCHER 564639 sr_no_br: 564639 sr_no_br_cl: 564639 sr_cl: FISCHER564639 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 30 mm Overall length 115 mm Material (bolt) Steel Surface treatment (bolt) None Thread dimension M10 n: FISCHER 564639 Piercing anchor FAZ II Plus 10/30 HCR high-corrosion steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 10/30 HCR high-corrosion steel kpn: 564639 kpn_dash: kpn_clear: 564639 bkpn: FISCHER 564639 bkpn_clear: FISCHER 564639 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564639 sr_ns: FISCHER564639
r: 02020742 p: 19.34 pid: 12901 b: FISCHER q: 0 st: lt: 8 ean: 4006209920367 sr: FISCHER 92036 sr_no_br: 92036 sr_no_br_cl: 92036 sr_cl: FISCHER92036 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Anchoring depth 125 mm Width across flats 24 mm Effective length 10 - 50 mm Drill hole depth 180 mm Drilling diameter 18 mm n: FISCHER 92036 highbond anchor FHB-A dynamic 16 x 125/50 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The highest performance in class amongst dynamic anchors The fischer Highbond anchor dynamic FHB-A dyn is made of zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. During the setting process, the injection mortar FIS HB fills the annular gap in the fixture, and guarantees optimum load distribution. This allows for the absorption of dynamic alternating loads. The fischer Highbond anchor dynamic FHB-A dyn is ideally suited for fixing guide rails for elevators, industrial robots, or mobile portal and ceiling cranes in internal areas. Controlled expansion under dynamic stress due to cone shape Absorption of dynamic alternating loads via optimum load distribution Approved for cracked concrete The Highbond-anchor dynamic FHB-A dyn must be applied in combination with the Highbond-mortar FIS HB During the setting process, the injection mortar FIS HB fills the annular gap in the fixture, and ensures optimum load distribution. This allows for the absorption of dynamic alternating loads The cone shape of the FHB-A dyn anchor rod ensures a controlled expansion under dynamic stress, thus allowing for use in cracked concrete The anchor rod FHB-A dyn is also available made from high corrosion-resistant steel. This makes it suitable for use in aggressive atmospheres, for example in tunnels The Highbond anchor dynamic system can achieve even greater shear loads thanks to the additional sleeve of the anchor rod FHB-A dyn V, and therefore provides an increased level of safety The ETA for static and quasi-static loads allows the use of sizes M12 and M16 also for the anchoring base steel fiber concrete Suitable for The injection system suitable for tensile zones consists of the Highbond dynamic anchor rod FHB-A dyn and the injection mortar FIS HB FHB dyn is approved for pre-positioned and push-through installation Extruding the mortar causes the two components to be mixed and activated in the static mixer The mortar bonds the entire surface of the anchor rod with the drill hole wall and seals the drill hole The centring sleeve centres the anchor in the fixture, thus ensuring a safe load application The lock nut prevents the nut from becoming loose Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Steel fiber reinforced concrete (M12 / M16) Application Jib cranes Gantry and overhead cranes Guide rails for elevators Tunnel ventilators (jet fans) Gantries in road construction Antennas and transmitter masts Industrial robots ds: dsc: kts: highbond anchor FHB-A dynamic 16 x 125/50 ev kpn: 92036 kpn_dash: kpn_clear: 92036 bkpn: FISCHER 92036 bkpn_clear: FISCHER 92036 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 92036 sr_ns: FISCHER92036
r: 02020601 p: 19.28 pid: 16171 b: FISCHER q: 0 st: lt: 8 ean: 4006209976227 sr: FISCHER 97622 sr_no_br: 97622 sr_no_br_cl: 97622 sr_cl: FISCHER97622 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm Anchoring depth 120 mm Width across flats 19 mm Effective length 25 mm Drill hole depth 135 mm Drilling diameter 14 mm n: FISCHER 97622 highbond anchor FHB II-A L M12 x 120/25 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tension loads - even outdoors. The fischer Highbond rod anchor FHB II-A L is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, silos, and heavy steel constructions are securely installed within external areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M12 x 120/25 stainless steel A4 kpn: 97622 kpn_dash: kpn_clear: 97622 bkpn: FISCHER 97622 bkpn_clear: FISCHER 97622 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97622 sr_ns: FISCHER97622
r: 02020221 p: 19.14 pid: 94559 b: FISCHER q: 0 st: lt: 8 ean: 4006209970706 sr: FISCHER 97070 sr_no_br: 97070 sr_no_br_cl: 97070 sr_cl: FISCHER97070 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Length 160 mm Anchoring depth 160 mm Width across flats 24 mm Effective length 100 mm Drill hole depth 175 mm Drilling diameter 18 mm n: FISCHER 97070 highbond anchor FHB II-A L M16 x 160/100 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tensile loads. The fischer Highbond rod anchor FHB II-A L is produced from zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that large machines and heavy steel constructions are securely installed within internal areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M16 x 160/100 ev kpn: 97070 kpn_dash: kpn_clear: 97070 bkpn: FISCHER 97070 bkpn_clear: FISCHER 97070 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97070 sr_ns: FISCHER97070
r: 02020200 p: 19.14 pid: 96813 b: FISCHER q: 0 st: lt: 8 ean: 4006209972977 sr: FISCHER 97297 sr_no_br: 97297 sr_no_br_cl: 97297 sr_cl: FISCHER97297 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 24 mm Length 170 mm Anchoring depth 170 mm Width across flats 36 mm Effective length 50 mm Drill hole depth 190 mm Drilling diameter 25 mm n: FISCHER 97297 highbond anchor FHB II-A S M24 x 170/50 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete with the least installation effort. The fischer Highbond rod anchor FHB II-A S is produced from zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that railings, machines and heavy steel constructions are securely installed within internal areas. Reduces anchorage depth, lowers expense when drilling and installing. This saves costs Through-type installations without additional aids. This saves time Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The reduced anchorage depth of the FHB II-A S minimises the drilling and installation effort. In addition using the combination with FHB II-P/-PF capsule no drill hole cleaning is required. Thus allowing for an especially economical and time-saving fixing With the anchor rod FHB II-A S, the drill bit diameter is the same as the thread diameter. This allows for push-through installation without any tools and reduces the amount of mortar required The cone shape of the anchor rod FHB II-A S is optimised for small axial and edge distances in cracked concrete, as well as thin concrete members. As a result, it is suitable for a wide range of applications The anchor rod FHB II-A S is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application Suitable for The FHB II-A S is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-A S, the drill bit diameter is the same as the thread diameter, similar to with an anchor bolt The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Suitable for: Guard rails Façades Staircases Steel brackets Masts Rash protection Steelwork constructions Timber constructions Ideal for: Push-through installation ds: dsc: kts: highbond anchor FHB II-A S M24 x 170/50 ev kpn: 97297 kpn_dash: kpn_clear: 97297 bkpn: FISCHER 97297 bkpn_clear: FISCHER 97297 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97297 sr_ns: FISCHER97297
r: 02020596 p: 18.63 pid: 16005 b: FISCHER q: 0 st: lt: 8 ean: 4006209976210 sr: FISCHER 97621 sr_no_br: 97621 sr_no_br_cl: 97621 sr_cl: FISCHER97621 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm Anchoring depth 120 mm Width across flats 19 mm Effective length 10 mm Drill hole depth 135 mm Drilling diameter 14 mm n: FISCHER 97621 highbond anchor FHB II-A L M12 x 120/10 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tension loads - even outdoors. The fischer Highbond rod anchor FHB II-A L is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, silos, and heavy steel constructions are securely installed within external areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M12 x 120/10 stainless steel A4 kpn: 97621 kpn_dash: kpn_clear: 97621 bkpn: FISCHER 97621 bkpn_clear: FISCHER 97621 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97621 sr_ns: FISCHER97621
r: 08096871 p: 17.79 pid: 176272 b: FISCHER q: 0 st: lt: 8 ean: 4048962462319 sr: FISCHER 564606 sr_no_br: 564606 sr_no_br_cl: 564606 sr_cl: FISCHER564606 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 24 mm Effective length 60 mm Overall length 235 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread dimension M24 n: FISCHER 564606 Piercing anchor FAZ II Plus 24/60 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 24/60 EV electrolytically galvanised steel kpn: 564606 kpn_dash: kpn_clear: 564606 bkpn: FISCHER 564606 bkpn_clear: FISCHER 564606 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564606 sr_ns: FISCHER564606
r: 02020559 p: 17.63 pid: 96446 b: FISCHER q: 0 st: lt: 8 ean: 4006209976418 sr: FISCHER 97641 sr_no_br: 97641 sr_no_br_cl: 97641 sr_cl: FISCHER97641 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Anchoring depth 95 mm Width across flats 24 mm Effective length 30 mm Drill hole depth 110 mm Drilling diameter 16 mm n: FISCHER 97641 highbond anchor FHB II-A S M16 x 95/30 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete with the least installation effort - even outdoors. The fischer Highbond rod anchor FHB II-A S A4 is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, railings, and steel constructions are securely installed within external areas. Reduces anchorage depth, lowers expense when drilling and installing. This saves costs Through-type installations without additional aids. This saves time Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The reduced anchorage depth of the FHB II-A S minimises the drilling and installation effort. In addition using the combination with FHB II-P/-PF capsule no drill hole cleaning is required. Thus allowing for an especially economical and time-saving fixing With the anchor rod FHB II-A S, the drill bit diameter is the same as the thread diameter. This allows for push-through installation without any tools and reduces the amount of mortar required The cone shape of the anchor rod FHB II-A S is optimised for small axial and edge distances in cracked concrete, as well as thin concrete members. As a result, it is suitable for a wide range of applications The anchor rod FHB II-A S is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application Suitable for The FHB II-A S is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-A S, the drill bit diameter is the same as the thread diameter, similar to with an anchor bolt The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Suitable for: Guard rails Façades Staircases Steel brackets Masts Rash protection Steelwork constructions Timber constructions Ideal for: Push-through installation ds: dsc: kts: highbond anchor FHB II-A S M16 x 95/30 stainless steel A4 kpn: 97641 kpn_dash: kpn_clear: 97641 bkpn: FISCHER 97641 bkpn_clear: FISCHER 97641 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97641 sr_ns: FISCHER97641
r: 02137076 p: 16.87 pid: 21597 b: FISCHER q: 0 st: lt: 8 ean: 4006209502679 sr: FISCHER 50267 sr_no_br: 50267 sr_no_br_cl: 50267 sr_cl: FISCHER50267 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 20 mm Length 260 mm Material Stainless steel A4 Drilling diameter 25 mm n: FISCHER 50267 anchor rod RG M20 x 260 R stainless steel cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The proven rod anchor for external use with a mortar cartridge or injection mortar. The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas. Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge Stainless steel for outdoor use The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety Please refer to the approvals for the resin capsules and mortar used Suitable for Due to its oblique edge, the anchor rod RG M is particularly suitable for use in conjunction with resin capsules The anchor rod RG M is set using a hammer drill and the accompanying setting tool in rotating and hitting motions During setting, the oblique edge of the RG M destroys the capsule, and mixes and activates the mortar Use with injection mortar is also possible. Here, the anchor rod is manually inserted into the drill hole with a light rotating movement until it reaches the base of the hole Building materials In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete In connection with several fischer injection mortars approved or suitable for different building materials Application Anchorings with resin capsule RSB and RSB mini Anchorings with resin capsule RM II Anchorings with each of the fischer injection mortars FIS SB, FIS EM, FIS EB II, FIS V, FIS VL, FIS V Zero, FIS P Plus, FIS P, FIS EP and FIS Green ds: dsc: kts: anchor rod RG M20 x 260 R stainless steel kpn: 50267 kpn_dash: kpn_clear: 50267 bkpn: FISCHER 50267 bkpn_clear: FISCHER 50267 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 50267 sr_ns: FISCHER50267
r: 02019477 p: 16.487 pid: 10865 b: FISCHER q: 0 st: lt: 4 ean: 4006209484166 sr: FISCHER 48416 sr_no_br: 48416 sr_no_br_cl: 48416 sr_cl: FISCHER48416 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Drilling diameter 20 mm n: FISCHER EA II M16x65 A4 weft anchor stainless steel - 48416 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The internally threaded anchor made of stainless steel with a rim for simple Hammerset installation. The fischer Hammerset anchor EA II R is an internal threaded anchor made of stainless steel. The Hammerset anchor is set flush to the surface of the anchoring base using the hammer. With the setting tool EHS Plus or the machine setting tool EMS the sleeve is expanded by driving in the internal rod and expands against the drill hole wall. For correct expansion to take place, no torque must be applied to the screw or the threaded rod. The fischer Hammerset anchor EA II R is ideal for fixing steel constructions and formwork props in external areas with approval. Simple Hammerset installation: no slippage during assembly due to the pronounced edge on the anchor sleeve Use of standard metric screws and threaded rods lowers complexity Power-saving series installation with machine setting tool EA II S-SDS ETA approval for non-cracked concrete Made of stainless steel for fixings used outside The embossed rim prevents the anchor sleeve from slipping, thus ensuring a trouble-free hammerset installation The metric internal thread means that it is possible to use standard screws or threaded rods for the ideal adaptation to suit the intended use The EMS machine setting tool allows for effortless installation, particularly in the case of series installations The embossing that is applied when expanding with the EHS Plus setting tool offers a simple control of the anchoring and provides increased safety Fixing point at hef 25 mm prevents anchor of falling out of the drill hole before being expanded The black fixing point prevents the anchor from falling out of the drill hole during overhead installation Suitable for The EA II is suitable for pre-positioned installation Position the hammerset anchor in the drill hole and drive in flush to the surface of the anchor base using the hammer The sleeve is then expanded by driving in the internal bolt with the EHS Plus setting tool (alternative: EMS machine setting tool), and expanded against the drill hole wall The setting tools must sit on the rim of the anchor to ensure correct expansion Building materials Approved for: Concrete C20/25 to C50/60, cracked, for the multiple fixings of non-load-bearing systems Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Pipelines and ventilation ducts Sprinkler systems Cable conduits and wires Gratings Steel constructions Machines Consoles Shuttering props ds: dsc: kts: weft anchor stainless steel kpn: EA II M16x65 A4 kpn_dash: kpn_clear: EAIIM16x65A4 bkpn: FISCHER EA II M16x65 A4 bkpn_clear: FISCHER EAIIM16x65A4 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 48416 sr_ns: FISCHER48416
r: 08096897 p: 16.27 pid: 176295 b: FISCHER q: 0 st: lt: 8 ean: 4048962462555 sr: FISCHER 564630 sr_no_br: 564630 sr_no_br_cl: 564630 sr_cl: FISCHER564630 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 100 mm Overall length 223 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread dimension M16 n: FISCHER 564630 piercing anchor FAZ II Plus 16/100 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Stainless steel: maximum safety for outdoor use Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: piercing anchor FAZ II Plus 16/100 R stainless steel kpn: 564630 kpn_dash: kpn_clear: 564630 bkpn: FISCHER 564630 bkpn_clear: FISCHER 564630 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564630 sr_ns: FISCHER564630
r: 03374663 p: 16.198 pid: 176217 b: FISCHER q: 0 st: lt: 1 ean: 4048962540628 sr: FISCHER 574698 sr_no_br: 574698 sr_no_br_cl: 574698 sr_cl: FISCHER574698 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Net volume 150 ml Principal hazard property GHS07 Harmful or irritant Relative density 1 ADR packing group III ADR class 9 Packaging Can UN number UN3077 Conseils de prudence (P) P101; P102; P280; P501; P273; P391 H-statements H315; H317; H319; H400; H410 Hazard class GHS07 Harmful or irritant; GHS09 Environmental hazard Physical state Solid Flash point > 100 °C n: FISCHER 574698 injection mortar FIS VS Plus 150 C cn: INJECTION MORTAR cn2: INJECTION MORTAR cn_clear: INJECTIONMORTAR d: Product description The versatile injection mortar for installation in cracked concrete and masonry. The injection mortar FIS V Plus has numerous certifications, such as for cracked and uncracked concrete, solid and perforated masonry, aerated concrete as well as for special system applications. ETA certification for a service life of 100 years provides permanent safety for all applications. The certified use in water-filled boreholes allows an even wider range of applications, even under the harshest environmental conditions. The extensive range of accessories in the FIS V Plus range increases the flexibility of the system, enabling a wide range of applications. The fischer high-performance Injection Mortar FIS V Plus is the universal chemical anchor for the highest demands. The styrene-free vinylester hybrid mortar with its numerous anchors is certified for anchoring in cracked and uncracked concrete, solid and perforated masonry as well as aerated concrete. The FIS V Plus is used for bonding Anchor rods FIS A / RG M and internal threaded anchor RG M I. However, the injection mortar is also used in combination with reinforcement rods, the fischer renovation anchor VBS 8 and the spacer system TherMax. The shorter curing time of the variant FIS VW Plus allows a quick turnaround time even at low temperatures. Applications Steel structures Timber structures Handrails Façade systems Stairs Anchorage Machinery Awnings Awnings Fencing Brackets Building materials Certified for anchorages in: Concrete C20/25 to C50/60, cracked and uncracked Lightweight concrete hollow brick Concrete hollow brick Perforated clay brick Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid brick Certified as a system for: Bonding of reinforcement Renovation anchor VBS 8 Distance mounting system TherMax ds: dsc: kts: injection mortar FIS VS Plus 150 C kpn: 574698 kpn_dash: kpn_clear: 574698 bkpn: FISCHER 574698 bkpn_clear: FISCHER 574698 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Injection mortar | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer injection mortar sr_no_br_cl_ns: 574698 sr_ns: FISCHER574698
r: 87051311 p: 16.19 pid: 17220 b: FISCHER q: 0 st: lt: 8 ean: 4006209607848 sr: FISCHER 60784 sr_no_br: 60784 sr_no_br_cl: 60784 sr_cl: FISCHER60784 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm n: FISCHER FZA 12x50 M6 R Zykon female threaded anchor stainless steel - 60784 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The internally threaded anchor consists of stainless steel for optimum safety in cracked concrete. The fischer ZYKON internal threaded anchor FZA-I is an anchor made of stainless steel. The special drill bit FZUB is used to create the undercut drill hole in a single work step. The undercut anchor is set in the pre-positioned installation. The expansion sleeve is driven above the cone with the setting tool FZE Plus and fills the undercut drill hole with a positive fit. The fischer ZYKON internal threaded anchor FZA-I is ideal for fixing steel constructions, staircases, and temporary fixings within external areas in cracked concrete. Maximum safety due to a positive fit connection High flexibility due to using conventional metric screws and threaded rods Fast installation, no exchanging tools. This saves time and costs ETA approval for cracked concrete and fire resistance class R 120 Made of stainless steel for fixings used outside The special ZYKON undercut technology allows for a positive fit connection and ensures maximum safety, even in large cracks The metric internal thread means that it is possible to use standard screws or threaded rods for the ideal adaptation to suit the intended use The FZA-I allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility Furthermore, the ZYKON undercut anchor FZA-I offers all the benefits of the FZA Suitable for FZA-I with internal thread is suitable for pre-positioned installation The undercut drill hole is created using the special FZUB drill Once the anchor has been placed in the drill hole, the expansion sleeve is driven over the cone using the FZE Plus setting tool, and the undercut drill hole is filled with a positive fit Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates ds: dsc: kts: Zykon female threaded anchor stainless steel kpn: FZA 12x50 M6 R kpn_dash: kpn_clear: FZA12x50M6R bkpn: FISCHER FZA 12x50 M6 R bkpn_clear: FISCHER FZA12x50M6R c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 60784 sr_ns: FISCHER60784
