r: 02776794 p: 2.78 pid: 22098 b: FISCHER q: 0 st: lt: 8 ean: 4048962251579 sr: FISCHER 536874 sr_no_br: 536874 sr_no_br_cl: 536874 sr_cl: FISCHER536874 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 14 mm Max. useful length 10 mm Length 75 mm n: FISCHER 536874 concrete screw FBS II 14x75 10/- hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 14x75 10/- hexagon head kpn: 536874 kpn_dash: kpn_clear: 536874 bkpn: FISCHER 536874 bkpn_clear: FISCHER 536874 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536874 sr_ns: FISCHER536874
r: 02776778 p: 2.5 pid: 20433 b: FISCHER q: 0 st: lt: 6 ean: 4048962251548 sr: FISCHER 536871 sr_no_br: 536871 sr_no_br_cl: 536871 sr_cl: FISCHER536871 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 12 mm Max. useful length 50 mm Length 110 mm n: FISCHER 536871 concrete screw FBS II 12x110 50/35/10 hexagonal head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 12x110 50/35/10 hexagonal head kpn: 536871 kpn_dash: kpn_clear: 536871 bkpn: FISCHER 536871 bkpn_clear: FISCHER 536871 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536871 sr_ns: FISCHER536871
r: 02776777 p: 2.32 pid: 22095 b: FISCHER q: 0 st: lt: 5 ean: 4048962251531 sr: FISCHER 536870 sr_no_br: 536870 sr_no_br_cl: 536870 sr_cl: FISCHER536870 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 12 mm Max. useful length 25 mm Length 85 mm n: FISCHER 536870 concrete screw FBS II 12x85 25/10/- hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 12x85 25/10/- hexagon head kpn: 536870 kpn_dash: kpn_clear: 536870 bkpn: FISCHER 536870 bkpn_clear: FISCHER 536870 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536870 sr_ns: FISCHER536870
r: 02776769 p: 2.32 pid: 21319 b: FISCHER q: 0 st: lt: 34 ean: 4048962251494 sr: FISCHER 536866 sr_no_br: 536866 sr_no_br_cl: 536866 sr_cl: FISCHER536866 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Max. useful length 145 mm Length 200 mm n: FISCHER 536866 concrete screw FBS II 10x200 145/135/115 hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x200 145/135/115 hexagon head kpn: 536866 kpn_dash: kpn_clear: 536866 bkpn: FISCHER 536866 bkpn_clear: FISCHER 536866 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536866 sr_ns: FISCHER536866
r: 02776774 p: 2.04 pid: 21322 b: FISCHER q: 0 st: lt: 8 ean: 4048962251524 sr: FISCHER 536869 sr_no_br: 536869 sr_no_br_cl: 536869 sr_cl: FISCHER536869 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 12 mm Max. useful length 10 mm Length 70 mm n: FISCHER 536869 concrete screw FBS II 12x70 10/- hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 12x70 10/- hexagon head kpn: 536869 kpn_dash: kpn_clear: 536869 bkpn: FISCHER 536869 bkpn_clear: FISCHER 536869 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536869 sr_ns: FISCHER536869
r: 02776768 p: 1.85 pid: 22018 b: FISCHER q: 0 st: lt: 8 ean: 4048962251487 sr: FISCHER 536865 sr_no_br: 536865 sr_no_br_cl: 536865 sr_cl: FISCHER536865 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Length 160 mm Max. useful length 105 mm n: FISCHER 536865 concrete screw FBS II 10x160 105/95/75 hexagonal head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x160 105/95/75 hexagonal head kpn: 536865 kpn_dash: kpn_clear: 536865 bkpn: FISCHER 536865 bkpn_clear: FISCHER 536865 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536865 sr_ns: FISCHER536865
r: 02776765 p: 1.48 pid: 20707 b: FISCHER q: 0 st: lt: 5 ean: 4048962251470 sr: FISCHER 536864 sr_no_br: 536864 sr_no_br_cl: 536864 sr_cl: FISCHER536864 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Length 140 mm Max. useful length 85 mm n: FISCHER 536864 concrete screw FBS II 10x140 85/75/55 hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x140 85/75/55 hexagon head kpn: 536864 kpn_dash: kpn_clear: 536864 bkpn: FISCHER 536864 bkpn_clear: FISCHER 536864 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536864 sr_ns: FISCHER536864
r: 02776807 p: 1.29 pid: 22105 b: FISCHER q: 0 st: lt: 8 ean: 4048962251692 sr: FISCHER 536886 sr_no_br: 536886 sr_no_br_cl: 536886 sr_cl: FISCHER536886 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Max. useful length 40 mm Length 95 mm n: FISCHER 536886 concrete screw FBS II 10x95 40/30/10 countersunk head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x95 40/30/10 countersunk head kpn: 536886 kpn_dash: kpn_clear: 536886 bkpn: FISCHER 536886 bkpn_clear: FISCHER 536886 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536886 sr_ns: FISCHER536886
r: 02776806 p: 1.2 pid: 20441 b: FISCHER q: 0 st: lt: 8 ean: 4048962251685 sr: FISCHER 536885 sr_no_br: 536885 sr_no_br_cl: 536885 sr_cl: FISCHER536885 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Max. useful length 25 mm Length 80 mm n: FISCHER 536885 concrete screw FBS II 10x80 25/15/- countersunk head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x80 25/15/- countersunk head kpn: 536885 kpn_dash: kpn_clear: 536885 bkpn: FISCHER 536885 bkpn_clear: FISCHER 536885 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536885 sr_ns: FISCHER536885
r: 02776751 p: 1.2 pid: 20699 b: FISCHER q: 0 st: lt: 8 ean: 4048962251395 sr: FISCHER 536856 sr_no_br: 536856 sr_no_br_cl: 536856 sr_cl: FISCHER536856 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 8 mm Length 110 mm Max. useful length 60 mm n: FISCHER 536856 concrete screw FBS II 8x110 60/45 hexagon head with TX shank cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 8x110 60/45 hexagon head with TX shank kpn: 536856 kpn_dash: kpn_clear: 536856 bkpn: FISCHER 536856 bkpn_clear: FISCHER 536856 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536856 sr_ns: FISCHER536856
r: 02776750 p: 1.11 pid: 22007 b: FISCHER q: 150 st: 1 lt: 1 ean: 4048962251388 sr: FISCHER 536855 sr_no_br: 536855 sr_no_br_cl: 536855 sr_cl: FISCHER536855 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 8 mm Length 100 mm Max. useful length 50 mm n: FISCHER 536855 concrete screw FBS II 8x100 50/35 hexagon head with TX shank cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 8x100 50/35 hexagon head with TX shank kpn: 536855 kpn_dash: kpn_clear: 536855 bkpn: FISCHER 536855 bkpn_clear: FISCHER 536855 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536855 sr_ns: FISCHER536855
r: 02776803 p: 1.11 pid: 22102 b: FISCHER q: 0 st: lt: 8 ean: 4048962251654 sr: FISCHER 536882 sr_no_br: 536882 sr_no_br_cl: 536882 sr_cl: FISCHER536882 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 8 mm Max. useful length 40 mm Length 90 mm n: FISCHER 536882 concrete screw FBS II 8x90 40/25 countersunk head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 8x90 40/25 countersunk head kpn: 536882 kpn_dash: kpn_clear: 536882 bkpn: FISCHER 536882 bkpn_clear: FISCHER 536882 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536882 sr_ns: FISCHER536882
r: 02776804 p: 1.11 pid: 20715 b: FISCHER q: 0 st: lt: 8 ean: 4048962251678 sr: FISCHER 536884 sr_no_br: 536884 sr_no_br_cl: 536884 sr_cl: FISCHER536884 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Max. useful length 10 mm Length 65 mm n: FISCHER 536884 concrete screw FBS II 10x65 10/- countersunk head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x65 10/- countersunk head kpn: 536884 kpn_dash: kpn_clear: 536884 bkpn: FISCHER 536884 bkpn_clear: FISCHER 536884 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536884 sr_ns: FISCHER536884
r: 02776757 p: 1.06 pid: 22092 b: FISCHER q: 0 st: lt: 8 ean: 4048962251425 sr: FISCHER 536859 sr_no_br: 536859 sr_no_br_cl: 536859 sr_cl: FISCHER536859 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Max. useful length 15 mm Length 70 mm n: FISCHER 536859 concrete screw FBS II 10x70 15/5/- hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x70 15/5/- hexagon head kpn: 536859 kpn_dash: kpn_clear: 536859 bkpn: FISCHER 536859 bkpn_clear: FISCHER 536859 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536859 sr_ns: FISCHER536859
r: 02776749 p: 1.02 pid: 20695 b: FISCHER q: 0 st: lt: 8 ean: 4048962251371 sr: FISCHER 536854 sr_no_br: 536854 sr_no_br_cl: 536854 sr_cl: FISCHER536854 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 8 mm Length 90 mm Max. useful length 40 mm n: FISCHER 536854 concrete screw FBS II 8x90 40/25 hexagon head with TX recess cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 8x90 40/25 hexagon head with TX recess kpn: 536854 kpn_dash: kpn_clear: 536854 bkpn: FISCHER 536854 bkpn_clear: FISCHER 536854 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536854 sr_ns: FISCHER536854
r: 02776802 p: 0.92 pid: 22025 b: FISCHER q: 0 st: lt: 8 ean: 4048962251647 sr: FISCHER 536881 sr_no_br: 536881 sr_no_br_cl: 536881 sr_cl: FISCHER536881 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 8 mm Max. useful length 30 mm Length 80 mm n: FISCHER 536881 concrete screw FBS II 8x80 30/15 countersunk head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 8x80 30/15 countersunk head kpn: 536881 kpn_dash: kpn_clear: 536881 bkpn: FISCHER 536881 bkpn_clear: FISCHER 536881 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536881 sr_ns: FISCHER536881
r: 02776735 p: 0.83 pid: 22085 b: FISCHER q: 0 st: lt: 8 ean: 4048962251630 sr: FISCHER 536880 sr_no_br: 536880 sr_no_br_cl: 536880 sr_cl: FISCHER536880 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 8 mm Max. useful length 10 mm Length 60 mm n: FISCHER 536880 concrete screw FBS II 8x60 10/- countersunk head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 8x60 10/- countersunk head kpn: 536880 kpn_dash: kpn_clear: 536880 bkpn: FISCHER 536880 bkpn_clear: FISCHER 536880 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536880 sr_ns: FISCHER536880
