r: 87051357 p: 2.09 pid: 16040 b: FISCHER q: 0 st: lt: 8 ean: 4048962016826 sr: FISCHER 503142 sr_no_br: 503142 sr_no_br_cl: 503142 sr_cl: FISCHER503142 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 10 mm Overall length 70 mm Safety anchor Yes Drilling diameter 10 mm n: FISCHER FH II 10/10 B safety anchor with nut zinc plated - 503142 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The through bolt anchor with threaded bolts with sophisticated design in cracked concrete. The fischer high-performance anchor FH II B with threaded bolt is a sleeve anchor made of zinc-plated steel. The anchor is set in the time-saving through-type installation. When tightening the anchor, the cone is pulled into the expansion sleeve and expands it against the hole wall. The black plastic ring prevents the anchor from rotating and absorbs the torque slippage. This means that the fixture is pulled towards the anchoring base. The fischer high-performance anchor FH II B with threaded bolt is ideally suited to fix railings, steel constructions, and cable trays in cracked and non-cracked concrete. With threaded bolts The ideal combination of screw shank and sleeve enables a high transverse load capacity and fewer fixing points The optimised geometry intelligently reduces the setting energy and thus ensures a force-saving assembly The international approvals guarantee maximum safety and the best performance. The European Technical Assessment even cover use in earthquake zones (seismic C1 and C2) The practical fixing using washers and nuts allows for the ultimate removal of the attachment if required later The design between the bolt and the sleeve ensures high shear load-bearing capacity. Thus, fewer fixing points are required The optimised geometry intelligently reduces the energy required for assembly The approval regulates the use of hollow drills Suitable for The FH II is suitable for push-through installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall The black plastic ring prevents rotation when tightening the anchor, and acts as a crumple zone to take the torque slippage so that the fixture is pulled onto the anchor base Available head shapes for flexible design solutions:Countersunk head (type SK), hexagon head (type S), bolt version with nut and washer (type B) and cap nut (type H) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Guard rails Staircases Consoles Steel constructions Ladders Cable trays Machines Gates Façades Gratings ds: dsc: kts: safety anchor with nut zinc plated kpn: FH II 10/10 B kpn_dash: kpn_clear: FHII1010B bkpn: FISCHER FH II 10/10 B bkpn_clear: FISCHER FHII1010B c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 503142 sr_ns: FISCHER503142
r: 87051368 p: 2.09 pid: 16306 b: FISCHER q: 0 st: lt: 8 ean: 4048962016734 sr: FISCHER 503133 sr_no_br: 503133 sr_no_br_cl: 503133 sr_cl: FISCHER503133 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 10 mm Overall length 70 mm Safety anchor Yes Drilling diameter 10 mm n: FISCHER FH II 10/10 S safety anchor with hexagonal head zinc plated - 503133 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The through bolt anchor with sophisticated design in cracked concrete. The fischer high-performance anchor FH II S with hexagonal head is a sleeve anchor made of zinc-plated steel. The anchor is set in the time-saving through-type installation. When tightening the anchor, the cone is pulled into the expansion sleeve and expands it against the hole wall. The black plastic ring prevents the anchor from rotating and absorbs the torque slippage. This means that the fixture is pulled towards the anchoring base. The fischer high-performance anchor FH II S with hexagonal head is ideally suited to fix consoles, steel constructions, and cable trays in cracked and non-cracked concrete. The international approvals guarantee maximum safety and maximum performance. Also for applications in earthquake regions (seismic C1 and C2) The ideal combination of screw shank and sleeve enables a high transverse load capacity and fewer fixing points The optimised geometry intelligently reduces the setting energy and thus ensures a force-saving assembly The international approvals guarantee maximum safety and the best performance. The European Technical Assessment even cover use in earthquake zones (seismic C1 and C2) The low profile of the screw head ensures for a discreet fixing The design between the bolt and the sleeve ensures high shear load-bearing capacity. Thus, fewer fixing points are required The optimised geometry intelligently reduces the energy required for assembly The approval regulates the use of hollow drills Suitable for The FH II is suitable for push-through installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall The black plastic ring prevents rotation when tightening the anchor, and acts as a crumple zone to take the torque slippage so that the fixture is pulled onto the anchor base Available head shapes for flexible design solutions:Countersunk head (type SK), hexagon head (type S), bolt version with nut and washer (type B) and cap nut (type H) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Guard rails Staircases Consoles Steel constructions Ladders Cable trays Machines Gates Façades Gratings ds: dsc: kts: safety anchor with hexagonal head zinc plated kpn: FH II 10/10 S kpn_dash: kpn_clear: FHII1010S bkpn: FISCHER FH II 10/10 S bkpn_clear: FISCHER FHII1010S c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 503133 sr_ns: FISCHER503133
r: 02824749 p: 2.08 pid: 176014 b: FISCHER q: 0 st: lt: 8 ean: 4048962293357 sr: FISCHER 541909 sr_no_br: 541909 sr_no_br_cl: 541909 sr_cl: FISCHER541909 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Length 180 mm n: FISCHER 541909 tension sleeve FNH 8 x 180 cn: NAIL SLEEVE cn2: NAIL SLEEVE cn_clear: NAILSLEEVE d: Product description The user-friendly spring sleeve for light fixings in solid building materials. The fischer nail sleeve FNH is a user-friendly spring sleeve made out of corrosion-resistant steel. The nail sleeve is driven into the through-type installation in a time-saving manner with the hammer, and expands along its whole length in the drill hole. This allows timber and metal sub-constructions, metal profiles, and squared timbers to be fixed in solid building materials in a cost-effective manner in interior areas and temporarily in external areas. Knock in with the hammer - finished Fixing without screws and plugs. This saves time and lowers costs No plugs or screws are required for the one-piece nail sleeve. This guarantees a simple and easy installation The geometry of the nail sleeve makes it easy to push it into the drill hole. This saves time and money Suitable for The FNH nail sleeve is suitable for push-through installation The nail sleeve is hammered in and expands its entire length in the hole FNH is suitable for interior applications and for temporary external fixings Building materials Concrete Solid sand-lime brick Natural stone with dense structure Solid brick Application Squared timbers Substructures made of wood and metal Metal profiles ds: dsc: kts: tension sleeve FNH 8 x 180 kpn: 541909 kpn_dash: kpn_clear: 541909 bkpn: FISCHER 541909 bkpn_clear: FISCHER 541909 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Clamping sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer clamping sleeve sr_no_br_cl_ns: 541909 sr_ns: FISCHER541909
r: 02019271 p: 2.08 pid: 11056 b: FISCHER q: 0 st: lt: 8 ean: 4006209902684 sr: FISCHER 90268 sr_no_br: 90268 sr_no_br_cl: 90268 sr_cl: FISCHER90268 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 8 mm Overall length 84 mm Material Steel Surface treatment Zinc plated Safety anchor No Drilling diameter 12 mm n: FISCHER TA M8 T/25 S sleeve anchor push-through assembly zinc plated - 90268 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The installation-friendly push-through anchor for fixings in non-cracked concrete. The fischer heavy-duty anchor TA M-T is a push-through anchor for time-saving through-type installation made of zinc-plated steel. During installation the cone is pulled into the expansion sleeve and expands it against the hole wall. The heavy-duty anchor is ideal for fixing consoles, ladders, and steel constructions in non-cracked concrete. Simple assembly due to low setting energy Low axial and edge distances due to uniform load introduction ETA approval for non-cracked concrete The optimised geometry minimises setting energy and allows for use in extremely narrow spaces. This allows for user-friendly installation The three-part expansion sleeve creates even load distribution, thus allowing small edge and axial spacing. Thus the TA M-T is extremely flexible The detachable screw connection allows for surface flush removal Suitable for The TA M-T is suitable for push-through installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Handrails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: sleeve anchor push-through assembly zinc plated kpn: TA M8 T/25 S kpn_dash: kpn_clear: TAM8T25S bkpn: FISCHER TA M8 T/25 S bkpn_clear: FISCHER TAM8T25S c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 90268 sr_ns: FISCHER90268
r: 02330108 p: 2.06 pid: 176185 b: FISCHER q: 0 st: lt: 6 ean: 4006209902899 sr: FISCHER 90289 sr_no_br: 90289 sr_no_br_cl: 90289 sr_cl: FISCHER90289 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Length 200 mm n: FISCHER 90289 anchor rod FIS A M16 x 200 electrolytically zinc-plated 5.8 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The FIS A versatile rod anchor The fischer threaded rod FIS A is made from zinc-plated, steel grade 5. 8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors. The universal solution for various fischer injection mortars. For a manageable range and simpler storage Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs The anchor rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications The wide range of approved anchor rods FIS A from M6 to M30 allows for various applications Please refer to the approvals of the injection mortar used Suitable for The anchor rod FIS A is suitable for pre-positioned and push-through installation FIS A is set manually into the drill hole, by lightly rotating it until it reaches the drill hole base Building materials In connection with several fischer injection mortars the anchor rod FIS A is approved or suitable for different building materials Application Anchorings with each of the fischer injection mortars such as FIS V Plus, FIS V Zero, FIS PM, FIS SB, FIS EM Plus, FIS EB II, FIS V, FIS VL, FIS P Plus, FIS P, FIS EP and FIS Green ds: dsc: kts: anchor rod FIS A M16 x 200 electrolytically zinc-plated 5.8 kpn: 90289 kpn_dash: kpn_clear: 90289 bkpn: FISCHER 90289 bkpn_clear: FISCHER 90289 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 90289 sr_ns: FISCHER90289
r: 02776774 p: 2.04 pid: 21322 b: FISCHER q: 0 st: lt: 8 ean: 4048962251524 sr: FISCHER 536869 sr_no_br: 536869 sr_no_br_cl: 536869 sr_cl: FISCHER536869 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 12 mm Max. useful length 10 mm Length 70 mm n: FISCHER 536869 concrete screw FBS II 12x70 10/- hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 12x70 10/- hexagon head kpn: 536869 kpn_dash: kpn_clear: 536869 bkpn: FISCHER 536869 bkpn_clear: FISCHER 536869 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536869 sr_ns: FISCHER536869
r: 08096866 p: 2.04 pid: 176257 b: FISCHER q: 0 st: lt: 8 ean: 4048962462333 sr: FISCHER 564608 sr_no_br: 564608 sr_no_br_cl: 564608 sr_cl: FISCHER564608 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 20 mm Overall length 75 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread designation M6 n: FISCHER 564608 piercing anchor FAZ II Plus 6/20 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, now with even higher tensile strengths. Heavy loads can be secured in cracked concrete using the steel anchor. The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity. For example, the steel anchor is ideal for the anchoring of railings, cable trays, and consoles. Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Stainless steel: maximum safety for outdoor use Millimeter accurate adjustment to the loads due to the variable anchoring depths The first bolt anchor M6 with ETA evaluation option 1: for safe approved anchorages The tried-and-tested expansion clip ensures highest load capacity even with size M6 Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: piercing anchor FAZ II Plus 6/20 R stainless steel kpn: 564608 kpn_dash: kpn_clear: 564608 bkpn: FISCHER 564608 bkpn_clear: FISCHER 564608 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564608 sr_ns: FISCHER564608
r: 08096904 p: 2.04 pid: 176281 b: FISCHER q: 0 st: lt: 8 ean: 4048962462142 sr: FISCHER 564589 sr_no_br: 564589 sr_no_br_cl: 564589 sr_cl: FISCHER564589 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 50 mm Overall length 150 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M12 n: FISCHER 564589 Piercing anchor FAZ II Plus 12/50 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 12/50 EV electrolytically galvanised steel kpn: 564589 kpn_dash: kpn_clear: 564589 bkpn: FISCHER 564589 bkpn_clear: FISCHER 564589 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564589 sr_ns: FISCHER564589
r: 87991059 p: 2.02 pid: 176401 b: FISCHER q: 0 st: lt: 6 ean: 4006209902882 sr: FISCHER 90288 sr_no_br: 90288 sr_no_br_cl: 90288 sr_cl: FISCHER90288 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Length 175 mm Drilling diameter 18 mm n: FISCHER 90288 anchor rod FIS A M16 x 175 electrolytically zinc-plated 5.8 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The FIS A versatile rod anchor The fischer threaded rod FIS A is made from zinc-plated, steel grade 5. 8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors. The universal solution for various fischer injection mortars. For a manageable range and simpler storage Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs The anchor rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications The wide range of approved anchor rods FIS A from M6 to M30 allows for various applications Please refer to the approvals of the injection mortar used Suitable for The anchor rod FIS A is suitable for pre-positioned and push-through installation FIS A is set manually into the drill hole, by lightly rotating it until it reaches the drill hole base Building materials In connection with several fischer injection mortars the anchor rod FIS A is approved or suitable for different building materials Application Anchorings with each of the fischer injection mortars such as FIS V Plus, FIS V Zero, FIS PM, FIS SB, FIS EM Plus, FIS EB II, FIS V, FIS VL, FIS P Plus, FIS P, FIS EP and FIS Green ds: dsc: kts: anchor rod FIS A M16 x 175 electrolytically zinc-plated 5.8 kpn: 90288 kpn_dash: kpn_clear: 90288 bkpn: FISCHER 90288 bkpn_clear: FISCHER 90288 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 90288 sr_ns: FISCHER90288
r: 02890558 p: 2.02 pid: 176071 b: FISCHER q: 0 st: lt: 8 ean: 4048962153828 sr: FISCHER 518823 sr_no_br: 518823 sr_no_br_cl: 518823 sr_cl: FISCHER518823 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: For diameter 12 Physical state Solid Hazard class GHS05 Corrosive; GHS07 Harmful or irritant; GHS09 Environmental hazard H-statements H315; H317; H318; H335; H411 Conseils de prudence (P) P101; P102; P280; P305 + P351 + P338; P310 EUH-statements EUH208 Principal hazard property GHS05 Corrosive UN number UN3077 ADR class 9 ADR packing group III Flash point 100 °C n: FISCHER 518823 Superbond chemical capsule RSB 12 cn: CHEMICAL ANCHOR cn2: CHEMICAL ANCHOR cn_clear: CHEMICALANCHOR d: Product description The concrete all-rounder with the best performance. The fischer resin capsule RSB contains a hybrid mortar based on styrene-free vinyl ester. The resin capsule is a system component of the fischer Superbond system for fixing in cracked and non-cracked concrete. The components are fixed using the fischer rod anchor RG M made of zinc-plated steel, made of stainless steel, and made of highly corrosion-resistant steel, as well as the fischer internal threaded anchor RG MI. The fischer anchor rod is set with the composite anchor setting tool through rotating and hitting motions using a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. With the fischer Superbond resin capsule objects such as heavy-duty steel constructions, soundproof walls, and high racks can be fixed. Cost-effective processing due to pre-portioning Processing possible up to -30 ° C Ideal for overhead installation Ideal for water-filled drill holes Less cleaning work, glass particles in the capsules rough up the drill hole wall The pre-portioned resin capsule RSB is especially cost-effective for individual applications and overhead installations The ideal solution for difficult conditions and installations with no waiting time due to fast hardening: Approval-compliant processing down to -30°C, also approved for water-filled and diamond-drilled holes as well as for seismic applications in performance category C1 (only in conjunction with RG M) For each diameter, up to three anchorage depths can be realised with the threaded rod RG M through a combination of the resin capsules RSB mini The use of the internal threaded anchor RG M I enables the surface-flush removal of the fixture and the reuse of the fixing point The angular threaded rod RG M can be set for light dynamic loads with the resin capsule system RSB in sizes M12, M16, M20 and M24 in stainless steel R with the fischer filling set Suitable for The 2-component resin capsules RSB and RSB mini contain vinyl ester hybrid mortar with silane technology. They are suitable for pre-positioned installation During setting, the oblique edge of the anchoring element destroys the capsule, and mixes and activates the mortar The glass particles of the capsule body roughen the inside of the drill hole, which reduces the cleaning effort to just four blowing passes The mortar bonds the entire surface of the anchor rod with the drill hole wall and seals the drill hole Building materials Approved for anchorings in: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Natural stone with dense structure Application Heavy steel constructions Silo installations Tall shelving Sound barriers Guard rails Staircases ds: dsc: kts: Superbond chemical capsule RSB 12 kpn: 518823 kpn_dash: kpn_clear: 518823 bkpn: FISCHER 518823 bkpn_clear: FISCHER 518823 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Chemical anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer chemical anchor sr_no_br_cl_ns: 518823 sr_ns: FISCHER518823
r: 08096908 p: 1.98 pid: 176300 b: FISCHER q: 0 st: lt: 8 ean: 4048962462753 sr: FISCHER 564650 sr_no_br: 564650 sr_no_br_cl: 564650 sr_cl: FISCHER564650 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 30 mm Overall length 130 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M12 n: FISCHER 564650 Piercing anchor FAZ II Plus 12/30 GS EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description With large washer. For highest demands. Powerful and flexible. The fischer bolt anchor FAZ II Plus GS with a large washer is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the zinc-plated steel anchor. Due to the variable anchorage depths and simple mounting, the FAZ II Plus GS can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. Pre-assembled washer for components with slots. This simplifies alignment and saves time during installation Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths The FAZ II Plus GS are suitable for fixing steel fixtures with long holes thanks to the special washer, and help to reduce installation effort The significantly larger outer diameter of the washers for FAZ II Plus 16 GS ensures a larger supporting surface, and as such allows for use in wood construction Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The variable anchorage depths allow a millimetre-accurate adjustment to the loads Suitable for The FAZ II Plus GS is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved Building materials Approved for: Beton C20/25 bis C50/60, gerissen und ungerissen Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Anchor plates with slotted holes Façade sub-structures with slotted holes Timber constructions Tension anchor Anchoring of wooden beams ds: dsc: kts: Piercing anchor FAZ II Plus 12/30 GS EV electrolytically galvanised steel kpn: 564650 kpn_dash: kpn_clear: 564650 bkpn: FISCHER 564650 bkpn_clear: FISCHER 564650 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564650 sr_ns: FISCHER564650
r: 08096959 p: 1.95 pid: 176296 b: FISCHER q: 0 st: lt: 8 ean: 4048962462098 sr: FISCHER 564584 sr_no_br: 564584 sr_no_br_cl: 564584 sr_cl: FISCHER564584 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 100 mm Overall length 185 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M10 n: FISCHER 564584 Piercing anchor FAZ II Plus 10/100 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 10/100 EV electrolytically galvanised steel kpn: 564584 kpn_dash: kpn_clear: 564584 bkpn: FISCHER 564584 bkpn_clear: FISCHER 564584 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564584 sr_ns: FISCHER564584
r: 02316677 p: 1.92 pid: 21656 b: FISCHER q: 0 st: lt: 8 ean: 4006209801796 sr: FISCHER 80179 sr_no_br: 80179 sr_no_br_cl: 80179 sr_cl: FISCHER80179 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Length (Wall plug) 130 mm Drill hole depth - mm Material (wall plug) Polyamide (Nylon®) Wall plug type Toggle plug With screw No Application Construction board type (screw head) Drilling diameter 20 mm n: FISCHER 80179 KDH 8 tumbler plug cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The cavity fixing with hook and wide transition beams for different board thicknesses. With the fischer toggle fixing KD components such as lights can be fixed in gypsum plasterboard and gypsum fibreboard, chipboard, and hollow ceilings made of brick and concrete. The toggle fixing is inserted into the drill hole in the pre-positioned installation and flips open independently when behind the board. This does not require a special installation tool and allows for a fast, convenient installation. High load capacity due to good load distribution on the transition beams High flexibility due to a long thread. Use with various panel thicknesses and attachment thicknesses No installation tool necessary With hook Universal fixing for fastenings in a wide range of drywall and hollow wall materials When the metal crosspiece is pushed. through the drill hole, pull it firmly against the inner wall cavity by tugging the plastic pull ring on the outer wall Afterwards cut the plastic legs off and fasten the fixture with e. g. a screw or screw in a hook or an eyebolt according to your demands Suitable for pre-positioned installation Suitable for The gravity and spring toggle are suitable for pre-positioned installation When placed in the drill hole, the bearing elements of the gravity and spring toggle independently swing open behind the board No special installation tool required. For a fast and convenient installation The KM10 is specially suited to fixing wash basins and urinals into installation and cavity walls Building materials Gypsum plasterboard and gypsum fibreboards Cavity floor slabs made from bricks and concrete Chipboard Plywood Application Pictures Lighting Light shelves Towel rails Mirror cabinets Light cabinets Cable and pipe clips ds: dsc: kts: KDH 8 tumbler plug kpn: 80179 kpn_dash: kpn_clear: 80179 bkpn: FISCHER 80179 bkpn_clear: FISCHER 80179 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 80179 sr_ns: FISCHER80179
r: 02890456 p: 1.89 pid: 176037 b: FISCHER q: 0 st: lt: 8 ean: 4048962181005 sr: FISCHER 522725 sr_no_br: 522725 sr_no_br_cl: 522725 sr_cl: FISCHER522725 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Length (Wall plug) 180 mm Drill hole depth - mm Material (wall plug) Polyamide (Nylon®) Wall plug type Hammer-in plug With screw Yes Application General type (screw head) T40; HEX 13 mm Drilling diameter 10 mm n: FISCHER 522725 construction plug SXRL 10 x 180 FUS hexagonal head cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The versatile with multiple anchorage depth The fischer frame fixing SXRL FUS is approved along with the fischer hexagon head screw with moulded washer and integrated bit holder TX40 for multiple fixings of non-load-bearing systems in masonry, concrete, and aerated concrete. The two expansion zones in the fixing induce forces equally into perforated masonry, these combine to form a long expansion element in aerated concrete and solid building material. The frame fixing with the safety screw made out of zinc-plated steel is suitable for fixings of façade, ceiling and roof substructures made of metal. ETA assessment with excellent load values: Safe multiple fixings of non-structural systems in concrete and masonry The long expansion element with three anchorage depths makes the SXRL versatile Loads are applied evenly to the building material thanks to the fixing geometry. This means that the fillets are not destroyed in the case of thin-walled building materials Simple to assemble: Ribs prevent plug rotation during installation The long expansion element with multiple anchorage depths of 50, 70 or 90 mm for SXRL 8 and SXRL 10 and 70 or 90 mm for SXRL 14 makes the SXRL an extremely versatile product Through the special geometry of the plug, the retention forces are evenly distributed in the drill hole The approval for single-point fixing in cracked concrete makes the SXRL the designated specialist in concrete particularly for tasks such as the installation of awning roofs and outdoor railings compared to steel anchors When it is to be set deep, the longer ribs prevent the plug from turning during installation The SXRL 14 is additionally approved for applications that are subject to pressure and may be used for façade structures that are installed without wall bracket with a spacing The SXRL with effective lengths up to 240 mm provides the right plug for every application Suitable for The SXRL is suitable for push-through installation In perforated brick masonry a force transmission that protects the substrate is guaranteed through the two expansion zones. The porous block fillets are not crushed by the second expansion zone an therefore serves to transmit the force In aerated concrete and solid building materials, the two expansion zones combine to form one long expansion element, thus providing for a uniform and flat distribution of the load into the substrate Countersunk head screws are recommended for fixing timber constructions. For metal constructions, plug with wide sleeve rim and hexagon head screws with moulded washer Building materials Approved for: Vertically perforated brick Aerated concrete Hollow blocks made from lightweight concrete Perforated sand-lime brick Thermal insulation blocks Solid block made from lightweight and normal weight concrete Solid brick Solid sand-lime brick Concrete >= C12/15 Also suitable for: Natural stone with dense structure Solid panel made from gypsum Application Façade, ceiling and roof substructures made of wood and metal Facade substructures under compression load (e. g. distance installation without a wall bracket) Windows Gates and doors Wardrobes Kitchen hanging cabinets Squared timbers Beams TV consoles Wall covering Metal brackets Metal supports Cable ducts Cable trays ds: dsc: kts: construction plug SXRL 10 x 180 FUS hexagonal head kpn: 522725 kpn_dash: kpn_clear: 522725 bkpn: FISCHER 522725 bkpn_clear: FISCHER 522725 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 522725 sr_ns: FISCHER522725
r: 08096917 p: 1.87 pid: 176286 b: FISCHER q: 0 st: lt: 8 ean: 4048962462746 sr: FISCHER 564649 sr_no_br: 564649 sr_no_br_cl: 564649 sr_cl: FISCHER564649 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 20 mm Overall length 120 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M12 n: FISCHER 564649 Piercing anchor FAZ II Plus 12/20 GS EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description With large washer. For highest demands. Powerful and flexible. The fischer bolt anchor FAZ II Plus GS with a large washer is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the zinc-plated steel anchor. Due to the variable anchorage depths and simple mounting, the FAZ II Plus GS can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. Pre-assembled washer for components with slots. This simplifies alignment and saves time during installation Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths The FAZ II Plus GS are suitable for fixing steel fixtures with long holes thanks to the special washer, and help to reduce installation effort The significantly larger outer diameter of the washers for FAZ II Plus 16 GS ensures a larger supporting surface, and as such allows for use in wood construction Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The variable anchorage depths allow a millimetre-accurate adjustment to the loads Suitable for The FAZ II Plus GS is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved Building materials Approved for: Beton C20/25 bis C50/60, gerissen und ungerissen Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Anchor plates with slotted holes Façade sub-structures with slotted holes Timber constructions Tension anchor Anchoring of wooden beams ds: dsc: kts: Piercing anchor FAZ II Plus 12/20 GS EV electrolytically galvanised steel kpn: 564649 kpn_dash: kpn_clear: 564649 bkpn: FISCHER 564649 bkpn_clear: FISCHER 564649 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564649 sr_ns: FISCHER564649
r: 08096868 p: 1.86 pid: 176231 b: FISCHER q: 0 st: lt: 8 ean: 4048962462326 sr: FISCHER 564607 sr_no_br: 564607 sr_no_br_cl: 564607 sr_cl: FISCHER564607 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 10 mm Overall length 65 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread designation M6 n: FISCHER 564607 Piercing anchor FAZ II Plus 6/10 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, now with even higher tensile strengths. Heavy loads can be secured in cracked concrete using the steel anchor. The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity. For example, the steel anchor is ideal for the anchoring of railings, cable trays, and consoles. Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Stainless steel: maximum safety for outdoor use Millimeter accurate adjustment to the loads due to the variable anchoring depths The first bolt anchor M6 with ETA evaluation option 1: for safe approved anchorages The tried-and-tested expansion clip ensures highest load capacity even with size M6 Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 6/10 R stainless steel kpn: 564607 kpn_dash: kpn_clear: 564607 bkpn: FISCHER 564607 bkpn_clear: FISCHER 564607 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564607 sr_ns: FISCHER564607
r: 02776768 p: 1.85 pid: 22018 b: FISCHER q: 0 st: lt: 8 ean: 4048962251487 sr: FISCHER 536865 sr_no_br: 536865 sr_no_br_cl: 536865 sr_cl: FISCHER536865 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Length 160 mm Max. useful length 105 mm n: FISCHER 536865 concrete screw FBS II 10x160 105/95/75 hexagonal head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x160 105/95/75 hexagonal head kpn: 536865 kpn_dash: kpn_clear: 536865 bkpn: FISCHER 536865 bkpn_clear: FISCHER 536865 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536865 sr_ns: FISCHER536865
r: 02870370 p: 1.82 pid: 176018 b: FISCHER q: 0 st: lt: 8 ean: 4048962153811 sr: FISCHER 518822 sr_no_br: 518822 sr_no_br_cl: 518822 sr_cl: FISCHER518822 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: For diameter 12 mm Physical state Solid Hazard class GHS05 Corrosive; GHS07 Harmful or irritant; GHS09 Environmental hazard H-statements H315; H317; H318; H335; H411 Conseils de prudence (P) P101; P102; P280; P305 + P351 + P338; P310 EUH-statements EUH208 Principal hazard property GHS05 Corrosive UN number UN3077 ADR class 9 ADR packing group III Flash point 100 °C n: FISCHER 518822 Superbond chemical capsule RSB 12 mini cn: CHEMICAL ANCHOR cn2: CHEMICAL ANCHOR cn_clear: CHEMICALANCHOR d: Product description The concrete all-rounder with two anchoring depths for high performance. The fischer resin capsule RSB mini contains a hybrid mortar based on styrene-free vinyl ester. The resin capsule is a system component of the fischer Superbond system for fixing in cracked and non-cracked concrete. The components are fixed with the fischer rod anchor RG M made of zinc-plated steel, made of stainless steel, and made of highly corrosion-resistant steel. The fischer anchor rod is set with the composite anchor setting tool through rotating and hitting motions using a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. With the fischer Superbond resin capsule objects such as heavy-duty steel constructions, soundproof walls, and high racks can be fixed. Higher load level due to use of two mortar cartridges. This saves on fixing points Cost-effective processing due to pre-portioning Processing possible up to -30 ° C Ideal for overhead installation Ideal for water-filled drill holes The pre-portioned resin capsule RSB is especially cost-effective for individual applications and overhead installations The ideal solution for difficult conditions and installations with no waiting time due to fast hardening: Approval-compliant processing down to -30°C, also approved for water-filled and diamond-drilled holes as well as for seismic applications in performance category C1 (only in conjunction with RG M) For each diameter, up to three anchorage depths can be realised with the threaded rod RG M through a combination of the resin capsules RSB mini The use of the internal threaded anchor RG M I enables the surface-flush removal of the fixture and the reuse of the fixing point The angular threaded rod RG M can be set for light dynamic loads with the resin capsule system RSB in sizes M12, M16, M20 and M24 in stainless steel R with the fischer filling set Suitable for The 2-component resin capsules RSB and RSB mini contain vinyl ester hybrid mortar with silane technology. They are suitable for pre-positioned installation During setting, the oblique edge of the anchoring element destroys the capsule, and mixes and activates the mortar The glass particles of the capsule body roughen the inside of the drill hole, which reduces the cleaning effort to just four blowing passes The mortar bonds the entire surface of the anchor rod with the drill hole wall and seals the drill hole Building materials Approved for anchorings in: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Natural stone with dense structure Application Heavy steel constructions Silo installations Tall shelving Sound barriers Guard rails Staircases ds: dsc: kts: Superbond chemical capsule RSB 12 mini kpn: 518822 kpn_dash: kpn_clear: 518822 bkpn: FISCHER 518822 bkpn_clear: FISCHER 518822 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Chemical anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer chemical anchor sr_no_br_cl_ns: 518822 sr_ns: FISCHER518822
r: 02873435 p: 1.81 pid: 175996 b: FISCHER q: 0 st: lt: 8 ean: 8001132944301 sr: FISCHER 94430 sr_no_br: 94430 sr_no_br_cl: 94430 sr_cl: FISCHER94430 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 8 mm Drilling diameter 12 mm Overall length 75 mm Material Steel Surface treatment Zinc plated Safety anchor No n: FISCHER 94430 Channel anchor TA M8x75 EN electrolytically galvanised cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description Anchor for temporary fixing in hollow core concrete slabs without approval The fischer Hose anchor TA M NL is a sleeve anchor with female thread suitable for temporary fixing in hollow-core concrete slab floors. The optimized anchor geometry minimizes the energy required for installation. During assembly, the cone is pulled into the expansion sleeve, which then spreads into the wall of the channel. The triple spreading sleeve guarantees the even distribution of the load. After disassembly, no protruding parts remain in the drillhole, thus preventing the risk of accidents. Easy assembly due to small efforts during application Very suitable for temporary anchoring of struts in hollow-core slab floors No protruding parts after disassembly The fischer Hose anchor TA M-NL is suitable for use in hollow-core concrete slab elements with a thickness of >= 40 mm. The fischer Hulsanker TA M-NL is multifunctional and suitable for push-through installation. In addition, the anchor is detachable (sleeve stays behind in the channel plate). The anchor is available as standard in electrolytically galvanized steel Suitable for The TAM NL is suitable for push-through installation During tightening, the cone is pulled into the sleeve, so that it is clamped against the borehole wall The drilling process is decisive for the strength of the fastening. It is essential that the thickness of the shell is not further reduced by the concrete at the rear of the borehole. We first recommend to pre-drill 10 mm with a drill diameter and then drill with the specified drill diameter Building materials Suitable for: Concrete C12/15 Natural stone with dense structure Hollow core concrete slabs For fixing of: Temporary fixings like bracings Application Temporary fixings of braces in hollow core concrete slabs ds: dsc: kts: Channel anchor TA M8x75 EN electrolytically galvanised kpn: 94430 kpn_dash: kpn_clear: 94430 bkpn: FISCHER 94430 bkpn_clear: FISCHER 94430 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 94430 sr_ns: FISCHER94430
r: 02907555 p: 1.79 pid: 176073 b: FISCHER q: 0 st: lt: 8 ean: 4048962265231 sr: FISCHER 538661 sr_no_br: 538661 sr_no_br_cl: 538661 sr_cl: FISCHER538661 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: n: FISCHER 538661 hammer head screw FHS CLIX 10 x 100 cn: HAMMER HEAD BOLT cn2: HAMMER HEAD BOLT cn_clear: HAMMERHEADBOLT d: Product description Hammer-head bolt for quick and easy fixing in FLS channels The fischer T-head bolt FHS Clix is a fixing element for securely connecting pipe clamps with the fischer mounting channel system FLS. The T-head bolt FHS Clix is securely connected by means of a 90° rotation. The FHS Clix is available in the sizes M8 and M10 and in the lengths 30 to 100 mm. The special contact tongue on the FHS Clix ensures the required contact pressure of the fixing element in the FLS channel in order to ensure safe adjustment during assembly. In addition, the pronounced teeth in the channel nut enable precise and safe positioning in the FLS mounting channels and make the installation process easier. The galvanised zinc version is suitable for installation in buildings. The fire protection certificate provides added safety in the case of the channel nut. For easy connection of pipe clamps to FLS channels by means of grub screws and retaining claws Quick assembly by 90° rotation of the hammerhead screw in the rail Precise locking and secure hold of the FHS Clix in the rail due to serration of the sliding nut Fire protection test R120 MLAR R30 sample cable system test Application-appropriate corrosion protection through galvanisation For use in dry interior areas The special spring leg at the FHS Clix guarantees the necessary contact pressure of the connector to the channel to help for a secure adjustment during installation The teeth on the sliding nut enable an exact and secure positioning in the FLS channel and ease the installation of connector elements The clix-connector element with 90°-turn for connecting enables an easy post-installation in set channels to save time and money The especially developed stop element on the FHS Clix connector guarantees the accurate 90°-turn of the connectors in the channel to ensure a safe and precise installation Application FHS Clix is suitable for connecting pipe clamps with the channel For use in dry interior areas ds: dsc: kts: hammer head screw FHS CLIX 10 x 100 kpn: 538661 kpn_dash: kpn_clear: 538661 bkpn: FISCHER 538661 bkpn_clear: FISCHER 538661 c_path: Home / Fasteners and machine components / Fasteners / Bolts / Hammer head bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer bolts / Fischer hammer head bolt sr_no_br_cl_ns: 538661 sr_ns: FISCHER538661
