r: 01310019 p: 16.1 pid: 7163 b: SKF q: 0 st: lt: 10 ean: 7316570533132 sr: SKF G 50X58X4 sr_no_br: G 50X58X4 sr_no_br_cl: G50X58X4 sr_cl: SKFG50X58X4 sr_dash: sold: 32.2 p_range: none act: 1 avo: av: Inner diameter 50 mm Outer diameter 58 mm Width 4 mm n: SKF G 50X58X4 radial shaft seal 50 mm x 58 mm x 4 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 50 mm x 58 mm x 4 mm kpn: G 50X58X4 kpn_dash: kpn_clear: G50X58X4 bkpn: SKF G 50X58X4 bkpn_clear: SKF G50X58X4 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G50X58X4 sr_ns: SKFG50X58X4
r: 01311021 p: 54.06 pid: 8605 b: SKF q: 0 st: lt: 8 ean: 7316570850604 sr: SKF G 70X78X5 sr_no_br: G 70X78X5 sr_no_br_cl: G70X78X5 sr_cl: SKFG70X78X5 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 70 mm Outer diameter 78 mm Width 5 mm n: SKF G 70X78X5 radial shaft seal 70 mm x 78 mm x 5 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 70 mm x 78 mm x 5 mm kpn: G 70X78X5 kpn_dash: kpn_clear: G70X78X5 bkpn: SKF G 70X78X5 bkpn_clear: SKF G70X78X5 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G70X78X5 sr_ns: SKFG70X78X5
r: 01311020 p: 20.19 pid: 9062 b: SKF q: 0 st: lt: 10 ean: 7316570668810 sr: SKF G 55X63X5 sr_no_br: G 55X63X5 sr_no_br_cl: G55X63X5 sr_cl: SKFG55X63X5 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 55 mm Outer diameter 63 mm Width 5 mm n: SKF G 55X63X5 radial shaft seal 55 mm x 63 mm x 5 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 55 mm x 63 mm x 5 mm kpn: G 55X63X5 kpn_dash: kpn_clear: G55X63X5 bkpn: SKF G 55X63X5 bkpn_clear: SKF G55X63X5 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G55X63X5 sr_ns: SKFG55X63X5
r: 01310169 p: 19.14 pid: 7897 b: SKF q: 0 st: lt: 10 ean: 7316570676235 sr: SKF G 37X47X4 sr_no_br: G 37X47X4 sr_no_br_cl: G37X47X4 sr_cl: SKFG37X47X4 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 37 mm Outer diameter 47 mm Width 4 mm n: SKF G 37X47X4 radial shaft seal 37 mm x 47 mm x 4 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 37 mm x 47 mm x 4 mm kpn: G 37X47X4 kpn_dash: kpn_clear: G37X47X4 bkpn: SKF G 37X47X4 bkpn_clear: SKF G37X47X4 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G37X47X4 sr_ns: SKFG37X47X4
r: 01310155 p: 18.02 pid: 8489 b: SKF q: 0 st: lt: 12 ean: 7316570049817 sr: SKF G 17X25X3 sr_no_br: G 17X25X3 sr_no_br_cl: G17X25X3 sr_cl: SKFG17X25X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 17 mm Outer diameter 25 mm Width 3 mm n: SKF G 17X25X3 radial shaft seal 17 mm x 25 mm x 3 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 17 mm x 25 mm x 3 mm kpn: G 17X25X3 kpn_dash: kpn_clear: G17X25X3 bkpn: SKF G 17X25X3 bkpn_clear: SKF G17X25X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G17X25X3 sr_ns: SKFG17X25X3
r: 01311018 p: 13.54 pid: 9060 b: SKF q: 0 st: lt: 10 ean: 7316571105727 sr: SKF G 38X48X4 sr_no_br: G 38X48X4 sr_no_br_cl: G38X48X4 sr_cl: SKFG38X48X4 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 38 mm Outer diameter 48 mm Width 4 mm n: SKF G 38X48X4 radial shaft seal 38 mm x 48 mm x 4 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 38 mm x 48 mm x 4 mm kpn: G 38X48X4 kpn_dash: kpn_clear: G38X48X4 bkpn: SKF G 38X48X4 bkpn_clear: SKF G38X48X4 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G38X48X4 sr_ns: SKFG38X48X4
r: 01310168 p: 11.97 pid: 9055 b: SKF q: 0 st: lt: 10 ean: 7316570836530 sr: SKF G 35X45X4 sr_no_br: G 35X45X4 sr_no_br_cl: G35X45X4 sr_cl: SKFG35X45X4 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 35 mm Outer diameter 45 mm Width 4 mm n: SKF G 35X45X4 radial shaft seal 35 mm x 45 mm x 4 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 35 mm x 45 mm x 4 mm kpn: G 35X45X4 kpn_dash: kpn_clear: G35X45X4 bkpn: SKF G 35X45X4 bkpn_clear: SKF G35X45X4 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G35X45X4 sr_ns: SKFG35X45X4
r: 15992252 p: 10.135 pid: 172434 b: SKF q: 0 st: lt: 8 ean: 07316572550793 sr: SKF 44X60X10 HMS5 RG sr_no_br: 44X60X10 HMS5 RG sr_no_br_cl: 44X60X10HMS5RG sr_cl: SKF44X60X10HMS5RG sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 44 mm Width 10 mm Material NBR - Nitrile-Butadiene Rubber - Nitrile Outer diameter 60 mm n: SKF 44X60X10 HMS5 RG radial shaft seal with rubber outer diameter and single sealing lip, for oil or grease cn: OIL SEAL cn2: OIL SEAL cn_clear: OILSEAL d: Product description Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. HMS5 seals are designed with a rubber outside diameter. They have a conventional sealing lip made of elastomer with a garter spring to maintain the right radial load. High pumping rate With garter spring Accommodate misalignment ds: dsc: kts: radial shaft seal with rubber outer diameter and single sealing lip, for oil or grease kpn: 44X60X10 HMS5 RG kpn_dash: kpn_clear: 44X60X10HMS5RG bkpn: SKF 44X60X10 HMS5 RG bkpn_clear: SKF 44X60X10HMS5RG c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Oil seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf oil seal sr_no_br_cl_ns: 44X60X10HMS5RG sr_ns: SKF44X60X10HMS5RG
r: 01310149 p: 9.26 pid: 9053 b: SKF q: 0 st: lt: 10 ean: 7316571087306 sr: SKF G 14X22X3 sr_no_br: G 14X22X3 sr_no_br_cl: G14X22X3 sr_cl: SKFG14X22X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 14 mm Outer diameter 22 mm Width 3 mm n: SKF G 14X22X3 radial shaft seal 14 mm x 22 mm x 3 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 14 mm x 22 mm x 3 mm kpn: G 14X22X3 kpn_dash: kpn_clear: G14X22X3 bkpn: SKF G 14X22X3 bkpn_clear: SKF G14X22X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G14X22X3 sr_ns: SKFG14X22X3
r: 01310152 p: 9.17 pid: 7893 b: SKF q: 0 st: lt: 12 ean: 7316570605587 sr: SKF G 16X22X3 sr_no_br: G 16X22X3 sr_no_br_cl: G16X22X3 sr_cl: SKFG16X22X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 16 mm Outer diameter 22 mm Width 3 mm n: SKF G 16X22X3 radial shaft seal 16 mm x 22 mm x 3 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 16 mm x 22 mm x 3 mm kpn: G 16X22X3 kpn_dash: kpn_clear: G16X22X3 bkpn: SKF G 16X22X3 bkpn_clear: SKF G16X22X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G16X22X3 sr_ns: SKFG16X22X3
r: 01310146 p: 8.96 pid: 7166 b: SKF q: 0 st: lt: 10 ean: 7316571002316 sr: SKF G 13X19X3 sr_no_br: G 13X19X3 sr_no_br_cl: G13X19X3 sr_cl: SKFG13X19X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 13 mm Outer diameter 19 mm Width 3 mm n: SKF G 13X19X3 radial shaft seal 13 mm x 19 mm x 3 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 13 mm x 19 mm x 3 mm kpn: G 13X19X3 kpn_dash: kpn_clear: G13X19X3 bkpn: SKF G 13X19X3 bkpn_clear: SKF G13X19X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G13X19X3 sr_ns: SKFG13X19X3
r: 01310151 p: 8.73 pid: 8486 b: SKF q: 0 st: lt: 12 ean: 7316570552874 sr: SKF G 15X23X3 sr_no_br: G 15X23X3 sr_no_br_cl: G15X23X3 sr_cl: SKFG15X23X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 15 mm Outer diameter 23 mm Width 3 mm n: SKF G 15X23X3 radial shaft seal 15 mm x 23 mm x 3 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 15 mm x 23 mm x 3 mm kpn: G 15X23X3 kpn_dash: kpn_clear: G15X23X3 bkpn: SKF G 15X23X3 bkpn_clear: SKF G15X23X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G15X23X3 sr_ns: SKFG15X23X3
r: 01310139 p: 8.53 pid: 7888 b: SKF q: 0 st: lt: 12 ean: 7316570967012 sr: SKF G 8X12X3 sr_no_br: G 8X12X3 sr_no_br_cl: G8X12X3 sr_cl: SKFG8X12X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 8 mm Outer diameter 12 mm Width 3 mm n: SKF G 8X12X3 radial shaft seal 8 mm x 12 mm x 3 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 8 mm x 12 mm x 3 mm kpn: G 8X12X3 kpn_dash: kpn_clear: G8X12X3 bkpn: SKF G 8X12X3 bkpn_clear: SKF G8X12X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G8X12X3 sr_ns: SKFG8X12X3
r: 02029239 p: 7.34 pid: 2233 b: SKF q: 0 st: lt: 10 ean: 7316571194653 sr: SKF SD 20X28X4 sr_no_br: SD 20X28X4 sr_no_br_cl: SD20X28X4 sr_cl: SKFSD20X28X4 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 20 mm Outer diameter 28 mm Width 4 mm n: SKF SD 20X28X4 radial shaft seal 20 mm x 28 mm x 4 mm cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal 20 mm x 28 mm x 4 mm kpn: SD 20X28X4 kpn_dash: kpn_clear: SD20X28X4 bkpn: SKF SD 20X28X4 bkpn_clear: SKF SD20X28X4 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: SD20X28X4 sr_ns: SKFSD20X28X4
r: 01310147 p: 6.46 pid: 8597 b: SKF q: 0 st: lt: 10 ean: 7316570467482 sr: SKF G 14X20X3 sr_no_br: G 14X20X3 sr_no_br_cl: G14X20X3 sr_cl: SKFG14X20X3 sr_dash: sold: 0 p_range: none act: 1 avo: av: Inner diameter 14 mm Outer diameter 20 mm Width 3 mm n: SKF G 14X20X3 radial shaft seal cn: SHAFT SEAL cn2: SHAFT SEAL cn_clear: SHAFTSEAL d: Product description: Radial shaft seals are trailing seals used particularly for sealing oil-lubricated bearings. These ready-to-use elastomer seals usually have a metal reinforcement or housing The sealing lip is usually a nitrile rubber and is normally pressed against a contact surface on the shaft by means of a spring Depending on the seal material and the medium to be kept in or out, radial shaft seals can be used at temperatures between 60 and +190 °C The contact area between the seal lip and the contact surface is vital for the effectiveness of the seal The surface hardness of the contact surface should normally be at least 55 HRC, and the depth of hardening should be at least 0.3 mm Surface roughness according to ISO 4288:1996 should be within the guidelines of Ra = 0.2 to 0.8 mm In applications with low speeds, good lubrication and minimal contamination, a lower hardness can be used To prevent pumping of spiral grinding grooves, insert grinding is recommended If the radial shaft seal is to keep the lubricant inside the bearing housing, the seal should be mounted with the lip inwards If the main task is to keep out contaminants, the lip should point outwards ds: dsc: kts: radial shaft seal kpn: G 14X20X3 kpn_dash: kpn_clear: G14X20X3 bkpn: SKF G 14X20X3 bkpn_clear: SKF G14X20X3 c_path: Home / Technical and chemical products / Adhesives and sealants / Seals / Sealing rings / Shaft seal | Home / Our brands / Skf / Skf technical and chemical products / Skf adhesives and sealants / Skf seals / Skf sealing rings / Skf shaft seal sr_no_br_cl_ns: G14X20X3 sr_ns: SKFG14X20X3
