r: 02639425 p: 2.98 pid: 176207 b: FISCHER q: 0 st: lt: 4 ean: 4048962158373 sr: FISCHER 519023 sr_no_br: 519023 sr_no_br_cl: 519023 sr_cl: FISCHER519023 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: n: FISCHER 519023 aerated concrete anchor FPX-I M10 electrolytically galvanised steel cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The strong internal thread anchor with unique four-way expansion for fixings in aerated concrete. The fischer Aircrete anchor FPX-I is made of zinc-plated steel. After pre-drilling, the FPX-I is only driven in with the hammer. It is not necessary to clean the drill hole. The fischer Aircrete anchor is applied with a hex driver via a cordless screwdriver or via a ratchet. The cone is then pulled into the expansion sleeve. In this case the four wings create an undercut in the drill hole. After expansion, the hex socket is automatically released. The fischer Aircrete anchor FPX-I is ideally suited for fixing suspended ceilings, railings or kitchen cabinets in aerated concrete. The first approved metal anchor for aerated concrete High load capacity: Expanding wings create undercut. This saves on fixing points Simple and power-saving installation without an additional setting tool No rotation of the anchor Automatic setting control ensures maximum safety The FPX-I enables easy tightening via the hexagon wrench using a cordless screwdriver or ratchet and therefore offers top installation comfort The deformation-controlled expansion of the anchor with the hexagon wrench ensures safe, even and gentle installation The unique 4-way expansion of the FPX-I with a square expansion sleeve prevents the rotation of the anchor in the drill hole and ensures high tension and shear loads, which means fewer fixing points The releasing of the hexagonal wrench guarantees an automatical setting control for each installation process The first steel anchor with an ETA-Approval and fire protection certificate for fixings in aerated concrete enables use for safety-relevant fixings, too Suitable for The FPX-I with internal thread is suitable for pre-positioned installation Pre-drilling enables easy hammering in, even in high-strength aerated concrete. There is no need to clean the drill hole When the anchor is tightened with the hexagon wrench, the internal thread sleeve starts to rotate and the cone is pulled into the square expansion sleeve. The aerated concrete is compressed on the four sides and generates an undercut in the drill hole When reached the optimum expansion, the hexagon wrench is released automatically from the anchor Building materials Approved for: Aerated concrete with compressive strength 2 to 7 N/mm² Aerated concrete wall or ceiling boards with compressive strength 3. 3 to 4. 4 N/mm² Planked aerated concrete masonry, e. g. plastered, tiled, papered etc Application Suspended ceilings Cable trays Pipelines Ventilation ducts Guard rails/hand rails TV consoles Kitchen cupboards Stand-off installations ds: dsc: kts: aerated concrete anchor FPX-I M10 electrolytically galvanised steel kpn: 519023 kpn_dash: kpn_clear: 519023 bkpn: FISCHER 519023 bkpn_clear: FISCHER 519023 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 519023 sr_ns: FISCHER519023
r: 02890559 p: 2.97 pid: 176061 b: FISCHER q: 0 st: lt: 8 ean: 4048962153842 sr: FISCHER 518825 sr_no_br: 518825 sr_no_br_cl: 518825 sr_cl: FISCHER518825 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: For diameter 16 Physical state Solid Hazard class GHS05 Corrosive; GHS07 Harmful or irritant; GHS09 Environmental hazard H-statements H315; H317; H318; H335; H411 Conseils de prudence (P) P101; P102; P280; P305 + P351 + P338; P310 EUH-statements EUH208 Principal hazard property GHS05 Corrosive UN number UN3077 ADR class 9 ADR packing group III Flash point 100 °C n: FISCHER 518825 Superbond chemical capsule RSB 16 cn: CHEMICAL ANCHOR cn2: CHEMICAL ANCHOR cn_clear: CHEMICALANCHOR d: Product description The concrete all-rounder with the best performance. The fischer resin capsule RSB contains a hybrid mortar based on styrene-free vinyl ester. The resin capsule is a system component of the fischer Superbond system for fixing in cracked and non-cracked concrete. The components are fixed using the fischer rod anchor RG M made of zinc-plated steel, made of stainless steel, and made of highly corrosion-resistant steel, as well as the fischer internal threaded anchor RG MI. The fischer anchor rod is set with the composite anchor setting tool through rotating and hitting motions using a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. With the fischer Superbond resin capsule objects such as heavy-duty steel constructions, soundproof walls, and high racks can be fixed. Cost-effective processing due to pre-portioning Processing possible up to -30 ° C Ideal for overhead installation Ideal for water-filled drill holes Less cleaning work, glass particles in the capsules rough up the drill hole wall The pre-portioned resin capsule RSB is especially cost-effective for individual applications and overhead installations The ideal solution for difficult conditions and installations with no waiting time due to fast hardening: Approval-compliant processing down to -30°C, also approved for water-filled and diamond-drilled holes as well as for seismic applications in performance category C1 (only in conjunction with RG M) For each diameter, up to three anchorage depths can be realised with the threaded rod RG M through a combination of the resin capsules RSB mini The use of the internal threaded anchor RG M I enables the surface-flush removal of the fixture and the reuse of the fixing point The angular threaded rod RG M can be set for light dynamic loads with the resin capsule system RSB in sizes M12, M16, M20 and M24 in stainless steel R with the fischer filling set Suitable for The 2-component resin capsules RSB and RSB mini contain vinyl ester hybrid mortar with silane technology. They are suitable for pre-positioned installation During setting, the oblique edge of the anchoring element destroys the capsule, and mixes and activates the mortar The glass particles of the capsule body roughen the inside of the drill hole, which reduces the cleaning effort to just four blowing passes The mortar bonds the entire surface of the anchor rod with the drill hole wall and seals the drill hole Building materials Approved for anchorings in: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Natural stone with dense structure Application Heavy steel constructions Silo installations Tall shelving Sound barriers Guard rails Staircases ds: dsc: kts: Superbond chemical capsule RSB 16 kpn: 518825 kpn_dash: kpn_clear: 518825 bkpn: FISCHER 518825 bkpn_clear: FISCHER 518825 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Chemical anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer chemical anchor sr_no_br_cl_ns: 518825 sr_ns: FISCHER518825
r: 08096932 p: 2.95 pid: 176330 b: FISCHER q: 0 st: lt: 5 ean: 4048962462166 sr: FISCHER 564591 sr_no_br: 564591 sr_no_br_cl: 564591 sr_cl: FISCHER564591 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 100 mm Overall length 200 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M12 n: FISCHER 564591 Piercing anchor FAZ II Plus 12/100 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 12/100 EV electrolytically galvanised steel kpn: 564591 kpn_dash: kpn_clear: 564591 bkpn: FISCHER 564591 bkpn_clear: FISCHER 564591 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564591 sr_ns: FISCHER564591
r: 08134130 p: 2.9 pid: 176402 b: FISCHER q: 0 st: lt: 8 ean: 4048962267440 sr: FISCHER 539027 sr_no_br: 539027 sr_no_br_cl: 539027 sr_cl: FISCHER539027 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Drilling diameter 10 mm Length (Wall plug) 50 mm Drill hole depth - mm Material (wall plug) Plastic Wall plug type Cavity wall plug With screw Yes With collar Yes Application General n: FISCHER 539027 Hollow wall plug DuoTec 10 S PH with round head screw (2 pcs) cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The assembly-friendly solution for heavy loads in sheet metal. A combination of two material components for more power. The flange sleeve reinforces the drill hole and enables significantly higher transverse forces. The curved handle enables obstacle detection before starting assembly. The flexible screw fastening allows the use of screws and hooks with different thread shapes. The fibreglass-reinforced plastic and metal insert ensure the absorption of high tensile and transverse forces in all types of sheet material. The soft, grey nylon contact side distributes the load over the entire sheet surface, minimising any weakening of the supporting building material. Common borehole diameters and a short rocker element ensure easy installation even in small or insulated hollow spaces. The white flange sleeve with locking function ensures fast and secure mounting of the plug in the drilled hole. With scale on the band for determining the required screw length (scale value + 20 mm). The unique functioning and the geometry of the fischer DuoTec plug allow for extremely heavy loads for rocker plugs. This reduces the number of fasteners in multiple fastenings and maximises safety. As part of the DuoLine, the DuoTec consists of two plastic components. The red and hard component of the plug's sleeve enables the uniform distribution of the load, while the grey and white prevent damage to the surface of the board during fastening and thus a load reduction. In applications in board materials, which have a hollow space behind them, the DuoTec is applied as a tumbling plug. In solid building materials, the plug can also be used as a spreader plug. Applications Suspended kitchen cabinets Wall cabinets Bookshelves Wardrobes Handrails Paintings Mirrors Lamps Heavy hanging baskets Building materials Suitable for: Plasterboard Gypsum fibreboard Wooden panels (e.g. OSB, chipboard, MDF, etc.) Steel plate Plastic sheets Concrete hollow brick Also suitable for: Solid materials such as concrete and wood ds: dsc: Scope of delivery 2x DuoTec 10 2x screw with cylinder head 5.0x 60 kts: Hollow wall plug DuoTec 10 S PH with round head screw (2 pcs) kpn: 539027 kpn_dash: kpn_clear: 539027 bkpn: FISCHER 539027 bkpn_clear: FISCHER 539027 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 539027 sr_ns: FISCHER539027
r: 02776793 p: 2.88 pid: 20709 b: FISCHER q: 0 st: lt: 8 ean: 4048962251562 sr: FISCHER 536873 sr_no_br: 536873 sr_no_br_cl: 536873 sr_cl: FISCHER536873 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 14 mm Length 150 mm Max. useful length 90 mm n: FISCHER 536873 concrete screw FBS II 12x150 90/75/50 hexagonal head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 12x150 90/75/50 hexagonal head kpn: 536873 kpn_dash: kpn_clear: 536873 bkpn: FISCHER 536873 bkpn_clear: FISCHER 536873 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536873 sr_ns: FISCHER536873
r: 08096899 p: 2.83 pid: 176288 b: FISCHER q: 0 st: lt: 8 ean: 4048962462777 sr: FISCHER 564652 sr_no_br: 564652 sr_no_br_cl: 564652 sr_cl: FISCHER564652 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 80 mm Overall length 180 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M12 n: FISCHER 564652 Piercing anchor FAZ II Plus 12/80 GS EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description With large washer. For highest demands. Powerful and flexible. The fischer bolt anchor FAZ II Plus GS with a large washer is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the zinc-plated steel anchor. Due to the variable anchorage depths and simple mounting, the FAZ II Plus GS can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. Pre-assembled washer for components with slots. This simplifies alignment and saves time during installation Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths The FAZ II Plus GS are suitable for fixing steel fixtures with long holes thanks to the special washer, and help to reduce installation effort The significantly larger outer diameter of the washers for FAZ II Plus 16 GS ensures a larger supporting surface, and as such allows for use in wood construction Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The variable anchorage depths allow a millimetre-accurate adjustment to the loads Suitable for The FAZ II Plus GS is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved Building materials Approved for: Beton C20/25 bis C50/60, gerissen und ungerissen Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Anchor plates with slotted holes Façade sub-structures with slotted holes Timber constructions Tension anchor Anchoring of wooden beams ds: dsc: kts: Piercing anchor FAZ II Plus 12/80 GS EV electrolytically galvanised steel kpn: 564652 kpn_dash: kpn_clear: 564652 bkpn: FISCHER 564652 bkpn_clear: FISCHER 564652 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564652 sr_ns: FISCHER564652
r: 02678256 p: 2.81 pid: 176204 b: FISCHER q: 0 st: lt: 6 ean: 4006209786635 sr: FISCHER 78663 sr_no_br: 78663 sr_no_br_cl: 78663 sr_cl: FISCHER78663 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Length (Wall plug) 43 mm Drill hole depth 50 mm Material (wall plug) Brass Wall plug type Brass plug With screw No With collar No Application Concrete type (screw head) Drilling diameter 20 mm n: FISCHER 78663 brass plug MS 16 x 43 cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The brass expansion fixing with metric thread. The fischer brass fixing MS is an expansion plug made of brass for holding a metric thread. The special fixing is set in the pre-positioned installation. When driving in the screw or the threaded rod the brass fixing expands and anchors itself in the drill hole. Above all, the fischer brass fixing MS is suitable for fixing shelves, flow heaters, and aggregates in solid building materials. Fast installation due to compact design No rotation due to non-slip surface structure Flexibility due to using conventional screws and threaded rods Surface flush removal possible The compact design of the brass fixing reduces the amount of drilling required, helping to ensure a fast installation The special surface structure of the MS prevents the fixing from rotating in the drill hole. This provides increased installation safety The internal thread allows for the use of standard metric screws or threaded rods, and for surface flush removal and reuse of the fixing point. This provides great flexibility Suitable for The MS brass fixing is suitable for pre-positioned and push-through installation Turning in the metric screw causes the front part of the brass fixing to expand, thus securely anchoring it in the substrate Calculating screw length for flush fixing installation: Fixing length + fixture thickness = min. screw length Suitable for metric screws and threaded bolts The brass fixing may have to be expanded slightly before installation by turning in the threaded screw Building materials Concrete Solid sand-lime brick Natural stone with dense structure Solid brick Application Cellar shelves Substructures made of wood and metal Boilers Aggregates Control boxes Curtain rails ds: dsc: kts: brass plug MS 16 x 43 kpn: 78663 kpn_dash: kpn_clear: 78663 bkpn: FISCHER 78663 bkpn_clear: FISCHER 78663 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 78663 sr_ns: FISCHER78663
r: 87051348 p: 2.8 pid: 16035 b: FISCHER q: 0 st: lt: 8 ean: 4048962016819 sr: FISCHER 503141 sr_no_br: 503141 sr_no_br_cl: 503141 sr_cl: FISCHER503141 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 6 mm Overall length 115 mm Material Steel Surface treatment Zinc plated Safety anchor Yes Drilling diameter 10 mm n: FISCHER FH II 10/50 H safety anchor with cap nut zinc plated - 503141 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The through bolt anchor with cover nut and sophisticated design in cracked concrete. The fischer high-performance anchor FH II H with cover nut is a sleeve anchor made of zinc-plated steel. The anchor is set in the time-saving through-type installation. When tightening the anchor, the cone is pulled into the expansion sleeve and expands it against the hole wall. The black plastic ring prevents the anchor from rotating and absorbs the torque slippage. This means that the fixture is pulled towards the anchoring base. The fischer high-performance anchor FH II H with cover nut is ideally suited to fix steel constructions, machines, and gates in cracked and non-cracked concrete. With cover nut The international approvals guarantee maximum safety and maximum performance. Also for applications in earthquake regions (seismic C1 and C2) The ideal combination of screw shank and sleeve enables a high transverse load capacity and fewer fixing points The optimised geometry intelligently reduces the setting energy and thus ensures a force-saving assembly The international approvals guarantee maximum safety and the best performance. The European Technical Assessment even cover use in earthquake zones (seismic C1 and C2) The protruding head for stable and robust fixings The design between the bolt and the sleeve ensures high shear load-bearing capacity. Thus, fewer fixing points are required The optimised geometry intelligently reduces the energy required for assembly The approval regulates the use of hollow drills Suitable for The FH II is suitable for push-through installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall The black plastic ring prevents rotation when tightening the anchor, and acts as a crumple zone to take the torque slippage so that the fixture is pulled onto the anchor base Available head shapes for flexible design solutions:Countersunk head (type SK), hexagon head (type S), bolt version with nut and washer (type B) and cap nut (type H) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Guard rails Staircases Consoles Steel constructions Ladders Cable trays Machines Gates Façades Gratings ds: dsc: kts: safety anchor with cap nut zinc plated kpn: FH II 10/50 H kpn_dash: kpn_clear: FHII1050H bkpn: FISCHER FH II 10/50 H bkpn_clear: FISCHER FHII1050H c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 503141 sr_ns: FISCHER503141
r: 02776770 p: 2.78 pid: 22021 b: FISCHER q: 0 st: lt: 8 ean: 4048962251500 sr: FISCHER 536867 sr_no_br: 536867 sr_no_br_cl: 536867 sr_cl: FISCHER536867 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 10 mm Max. useful length 175 mm Length 230 mm n: FISCHER 536867 concrete screw FBS II 10x230 175/165/145 hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again The fischer concrete screws FBS II 6-10 offer the innovative possibility for the ETA compliant application in masonry. This grants high security not only in concrete but also in many other applications in other substrates With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 10x230 175/165/145 hexagon head kpn: 536867 kpn_dash: kpn_clear: 536867 bkpn: FISCHER 536867 bkpn_clear: FISCHER 536867 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536867 sr_ns: FISCHER536867
r: 02776794 p: 2.78 pid: 22098 b: FISCHER q: 0 st: lt: 8 ean: 4048962251579 sr: FISCHER 536874 sr_no_br: 536874 sr_no_br_cl: 536874 sr_cl: FISCHER536874 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 14 mm Max. useful length 10 mm Length 75 mm n: FISCHER 536874 concrete screw FBS II 14x75 10/- hexagon head cn: CONCRETE SCREW cn2: CONCRETE SCREW cn_clear: CONCRETESCREW d: Product description The high-performance concrete screw for absolute installation ease. The fischer UltraCut FBS II is the perfect concrete screw for top installation comfort. The special saw tooth geometry enables fast cutting into the concrete. Drill hole cleaning is not required for installations in ceilings or floors. Thanks to the national approval, multiple usage for temporary anchorings (for example, formwork construction) is permitted. For the installation of the wall screw, we recommend a tangential impact driver with a compatible socket or a special TX bit. The concrete screw is ideal for the fixation of railings, protection barriers, cantilevers, and formwork bracings, for example. With up to 3 embedment depths, it allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete The approved adjustment for the concrete screws allows the screw to be unscrewed twice to align the attached part, and then to tighten the screw again With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses The special saw tooth geometry enables fast cutting into the concrete Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2 The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again The checking gauge allows for reuse in temporary fixings (e. g. inclined supports) covered by the national approval The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups Suitable for The UltraCut FBS II is recommended for the push-through installation Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control) Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Reinforcement of existing concrete structures Bricks of clay (EN771-1) Solid sand-lime brick (EN771-2) Perforated sand-lime brick (EN771-2) Also suitable for: Concrete C12/15 Solid building materials Masonry with a dense structure Application Guard rails Consoles/Base plates Metal profiles Shelving systems Protection barriers Results / beam anchors Temporary anchoring, e. g. of building site equipment Shuttering props Reinforcement of bridges Rehabilitation of old and ailing buildings Rehabilitation of car parks ds: dsc: kts: concrete screw FBS II 14x75 10/- hexagon head kpn: 536874 kpn_dash: kpn_clear: 536874 bkpn: FISCHER 536874 bkpn_clear: FISCHER 536874 c_path: Home / Fasteners and machine components / Fasteners / Screws / Concrete screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer concrete screw sr_no_br_cl_ns: 536874 sr_ns: FISCHER536874
r: 02381019 p: 2.77 pid: 176193 b: FISCHER q: 0 st: lt: 5 ean: 4048962158359 sr: FISCHER 519021 sr_no_br: 519021 sr_no_br_cl: 519021 sr_cl: FISCHER519021 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: n: FISCHER 519021 aerated concrete anchor FPX-I M6 electrolytically galvanised steel cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The strong internal thread anchor with unique four-way expansion for fixings in aerated concrete. The fischer Aircrete anchor FPX-I is made of zinc-plated steel. After pre-drilling, the FPX-I is only driven in with the hammer. It is not necessary to clean the drill hole. The fischer Aircrete anchor is applied with a hex driver via a cordless screwdriver or via a ratchet. The cone is then pulled into the expansion sleeve. In this case the four wings create an undercut in the drill hole. After expansion, the hex socket is automatically released. The fischer Aircrete anchor FPX-I is ideally suited for fixing suspended ceilings, railings or kitchen cabinets in aerated concrete. The first approved metal anchor for aerated concrete High load capacity: Expanding wings create undercut. This saves on fixing points Simple and power-saving installation without an additional setting tool No rotation of the anchor Automatic setting control ensures maximum safety The FPX-I enables easy tightening via the hexagon wrench using a cordless screwdriver or ratchet and therefore offers top installation comfort The deformation-controlled expansion of the anchor with the hexagon wrench ensures safe, even and gentle installation The unique 4-way expansion of the FPX-I with a square expansion sleeve prevents the rotation of the anchor in the drill hole and ensures high tension and shear loads, which means fewer fixing points The releasing of the hexagonal wrench guarantees an automatical setting control for each installation process The first steel anchor with an ETA-Approval and fire protection certificate for fixings in aerated concrete enables use for safety-relevant fixings, too Suitable for The FPX-I with internal thread is suitable for pre-positioned installation Pre-drilling enables easy hammering in, even in high-strength aerated concrete. There is no need to clean the drill hole When the anchor is tightened with the hexagon wrench, the internal thread sleeve starts to rotate and the cone is pulled into the square expansion sleeve. The aerated concrete is compressed on the four sides and generates an undercut in the drill hole When reached the optimum expansion, the hexagon wrench is released automatically from the anchor Building materials Approved for: Aerated concrete with compressive strength 2 to 7 N/mm² Aerated concrete wall or ceiling boards with compressive strength 3. 3 to 4. 4 N/mm² Planked aerated concrete masonry, e. g. plastered, tiled, papered etc Application Suspended ceilings Cable trays Pipelines Ventilation ducts Guard rails/hand rails TV consoles Kitchen cupboards Stand-off installations ds: dsc: kts: aerated concrete anchor FPX-I M6 electrolytically galvanised steel kpn: 519021 kpn_dash: kpn_clear: 519021 bkpn: FISCHER 519021 bkpn_clear: FISCHER 519021 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 519021 sr_ns: FISCHER519021
r: 08096864 p: 2.74 pid: 176246 b: FISCHER q: 0 st: lt: 8 ean: 4048962462883 sr: FISCHER 564663 sr_no_br: 564663 sr_no_br_cl: 564663 sr_cl: FISCHER564663 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 8 mm Effective length 10 mm Overall length 75 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread designation M8 n: FISCHER 564663 Piercing anchor FAZ II Plus 8/10 GS R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description With large washer. For highest demands. Powerful and flexible. The fischer bolt anchor FAZ II Plus GS stainless steel with a large washer is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the stainless steel anchor. Due to the variable anchorage depths and simple mounting, the FAZ II Plus GS stainless steel can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The stainless steel version is used to fix loads in outdoor areas. For example, the steel anchor with large washer is ideal for fixing steel components or façade substructures with slots. Pre-assembled washer for components with slots. This simplifies alignment and saves time during installation Quick and easy assembly without the need for drill hole cleaning (M8-M24) Stainless steel: maximum safety for outdoor use Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Millimeter accurate adjustment to the loads due to the variable anchoring depths Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD The FAZ II Plus GS are suitable for fixing steel fixtures with long holes thanks to the special washer, and help to reduce installation effort The significantly larger outer diameter of the washers for FAZ II Plus 16 GS ensures a larger supporting surface, and as such allows for use in wood construction Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The variable anchorage depths allow a millimetre-accurate adjustment to the loads Suitable for The FAZ II Plus GS is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved Building materials Approved for: Beton C20/25 bis C50/60, gerissen und ungerissen Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Anchor plates with slotted holes Façade sub-structures with slotted holes Timber constructions Tension anchor Anchoring of wooden beams ds: dsc: kts: Piercing anchor FAZ II Plus 8/10 GS R stainless steel kpn: 564663 kpn_dash: kpn_clear: 564663 bkpn: FISCHER 564663 bkpn_clear: FISCHER 564663 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564663 sr_ns: FISCHER564663
r: 87990164 p: 2.69 pid: 176388 b: FISCHER q: 0 st: lt: 5 ean: 4006209784150 sr: FISCHER 78415 sr_no_br: 78415 sr_no_br_cl: 78415 sr_cl: FISCHER78415 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: n: FISCHER 78415 aerated concrete anchor FTP M6 metal cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The metal anchor for metric screws for aerated concrete. The fischer turbo Aircrete anchor FTP M is a special fixing for fixings in aerated concrete. The metal anchor is inserted into the drill hole in the pre-positioned installation using an Allen key. The spiral external thread cuts a mechanical interlock in the building material. The fischer turbo Aircrete anchor FTP M is ideally suited to securely fix mirror cabinets, radiators, and TV consoles to aerated concrete. No setting tool necessary High retention forces due to interlocking in building materials Convenient assembly: reduced wear and tear Low axial and edge distances due to expansion pressure-free anchoring The Allen key chuck makes it possible to set the FTP M without the need for a special setting tool. This allows for a simple installation The FTP M achieves a very high load-bearing capacity in aerated concrete for increased safety The spiral-shaped outer thread taps itself into the aerated concrete with a positive fit. This means that it can be set without the need for much force The special geometry allows for an almost expansion-force-free anchoring. This allows for small edge and spacing distances, and avoids splitting in the case of plastered surfaces Suitable for The FTP M is suitable for pre-positioned installation The aircrete anchor taps itself into the aircrete with a positive fit during the installation process Suitable for metric screws with diameter 6 to 10 mm For installation with a hexagon socket: Size of the hexagon socket corresponds to screw diameter, e. g. FTP M6 is installed with hexagon socket size 6 For installation with cordless screwdriver: use a low torque and use the correct 6-kt bit FTP EM Building materials Aerated concrete Solid panel made from gypsum Application Pictures Lighting Shelves Mirror cabinets Curtain rails Cable and pipe clips Stand-off installations Radiators TV consoles ds: dsc: kts: aerated concrete anchor FTP M6 metal kpn: 78415 kpn_dash: kpn_clear: 78415 bkpn: FISCHER 78415 bkpn_clear: FISCHER 78415 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 78415 sr_ns: FISCHER78415
r: 02890457 p: 2.68 pid: 176046 b: FISCHER q: 0 st: lt: 8 ean: 4048962181012 sr: FISCHER 522726 sr_no_br: 522726 sr_no_br_cl: 522726 sr_cl: FISCHER522726 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Length (Wall plug) 200 mm Drill hole depth - mm Material (wall plug) Polyamide (Nylon®) Wall plug type Hammer-in plug With screw Yes Application General type (screw head) T40; HEX 13 mm Drilling diameter 10 mm n: FISCHER 522726 construction plug SXRL 10 x 200 FUS hexagonal head cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The versatile with multiple anchorage depth The fischer frame fixing SXRL FUS is approved along with the fischer hexagon head screw with moulded washer and integrated bit holder TX40 for multiple fixings of non-load-bearing systems in masonry, concrete, and aerated concrete. The two expansion zones in the fixing induce forces equally into perforated masonry, these combine to form a long expansion element in aerated concrete and solid building material. The frame fixing with the safety screw made out of zinc-plated steel is suitable for fixings of façade, ceiling and roof substructures made of metal. ETA assessment with excellent load values: Safe multiple fixings of non-structural systems in concrete and masonry The long expansion element with three anchorage depths makes the SXRL versatile Loads are applied evenly to the building material thanks to the fixing geometry. This means that the fillets are not destroyed in the case of thin-walled building materials Simple to assemble: Ribs prevent plug rotation during installation The long expansion element with multiple anchorage depths of 50, 70 or 90 mm for SXRL 8 and SXRL 10 and 70 or 90 mm for SXRL 14 makes the SXRL an extremely versatile product Through the special geometry of the plug, the retention forces are evenly distributed in the drill hole The approval for single-point fixing in cracked concrete makes the SXRL the designated specialist in concrete particularly for tasks such as the installation of awning roofs and outdoor railings compared to steel anchors When it is to be set deep, the longer ribs prevent the plug from turning during installation The SXRL 14 is additionally approved for applications that are subject to pressure and may be used for façade structures that are installed without wall bracket with a spacing The SXRL with effective lengths up to 240 mm provides the right plug for every application Suitable for The SXRL is suitable for push-through installation In perforated brick masonry a force transmission that protects the substrate is guaranteed through the two expansion zones. The porous block fillets are not crushed by the second expansion zone an therefore serves to transmit the force In aerated concrete and solid building materials, the two expansion zones combine to form one long expansion element, thus providing for a uniform and flat distribution of the load into the substrate Countersunk head screws are recommended for fixing timber constructions. For metal constructions, plug with wide sleeve rim and hexagon head screws with moulded washer Building materials Approved for: Vertically perforated brick Aerated concrete Hollow blocks made from lightweight concrete Perforated sand-lime brick Thermal insulation blocks Solid block made from lightweight and normal weight concrete Solid brick Solid sand-lime brick Concrete >= C12/15 Also suitable for: Natural stone with dense structure Solid panel made from gypsum Application Façade, ceiling and roof substructures made of wood and metal Facade substructures under compression load (e. g. distance installation without a wall bracket) Windows Gates and doors Wardrobes Kitchen hanging cabinets Squared timbers Beams TV consoles Wall covering Metal brackets Metal supports Cable ducts Cable trays ds: dsc: kts: construction plug SXRL 10 x 200 FUS hexagonal head kpn: 522726 kpn_dash: kpn_clear: 522726 bkpn: FISCHER 522726 bkpn_clear: FISCHER 522726 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 522726 sr_ns: FISCHER522726
r: 08096900 p: 2.67 pid: 176259 b: FISCHER q: 0 st: lt: 10 ean: 4048962462159 sr: FISCHER 564590 sr_no_br: 564590 sr_no_br_cl: 564590 sr_cl: FISCHER564590 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 80 mm Overall length 180 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M12 n: FISCHER 564590 Piercing anchor FAZ II Plus 12/80 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 12/80 EV electrolytically galvanised steel kpn: 564590 kpn_dash: kpn_clear: 564590 bkpn: FISCHER 564590 bkpn_clear: FISCHER 564590 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564590 sr_ns: FISCHER564590
r: 02896195 p: 2.64 pid: 176080 b: FISCHER q: 0 st: lt: 8 ean: 4048962265965 sr: FISCHER 538751 sr_no_br: 538751 sr_no_br_cl: 538751 sr_cl: FISCHER538751 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: n: FISCHER 538751 beam clamp TKR 31 cn: BEAM CLAMP cn2: BEAM CLAMP cn_clear: BEAMCLAMP d: Product description Clamping bracket for the fixing of channels to steel girders The fischer beam clamp TKR 31 is suitable for the fixing of pipes and channels directly to steel girders. The TKR 31 can be secured to all common steel girders thanks to the different lengths of the clamp sides. No drilling or welding is required for the fixing. The beam clamps can be dismounted. The galvanised zinc version is suitable for installation in buildings. Clamping bracket for direct connection of FUS channels to steel girders No drilling, no welding required Application-appropriate corrosion protection due to hot-dip galvanised surface For indoor and outdoor use The design of the bean clamp allows for fixing without drilling or welding The various lengths of the bean clamp sides allows for fixing on all standard steel beams The shape of the bean clamp guarantees the simple adjustment of the channel connection Application Fixing of FLS channels to steel girders, required are two beam clamps per fixing For use in dry interior areas ds: dsc: kts: beam clamp TKR 31 kpn: 538751 kpn_dash: kpn_clear: 538751 bkpn: FISCHER 538751 bkpn_clear: FISCHER 538751 c_path: Home / Fasteners and machine components / Fasteners / Im / Beam clamp | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer im / Fischer beam clamp sr_no_br_cl_ns: 538751 sr_ns: FISCHER538751
r: 08134127 p: 2.62 pid: 176379 b: FISCHER q: 0 st: lt: 8 ean: sr: FISCHER 537263 sr_no_br: 537263 sr_no_br_cl: 537263 sr_cl: FISCHER537263 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Drilling diameter 10 mm Length (Wall plug) 50 mm Drill hole depth - mm Material (wall plug) Plastic Wall plug type Cavity wall plug With screw Yes With collar Yes Application General n: FISCHER 537263 Hollow wall plug DuoTec 10 S with screw (2 pcs) cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The assembly-friendly solution for heavy loads in sheet metal. A combination of two material components for more power. The flange sleeve reinforces the drill hole and enables significantly higher transverse forces. The curved handle enables obstacle detection before starting assembly. The flexible screw fastening allows the use of screws and hooks with different thread shapes. The fibreglass-reinforced plastic and metal insert ensure the absorption of high tensile and transverse forces in all types of sheet material. The soft, grey nylon contact side distributes the load over the entire sheet surface, minimising any weakening of the supporting building material. Common borehole diameters and a short rocker element ensure easy installation even in small or insulated hollow spaces. The white flange sleeve with locking function ensures fast and secure mounting of the plug in the drilled hole. With scale on the band for determining the required screw length (scale value + 20 mm). The unique functioning and geometry of the dowel allow extremely heavy loads for rocker plugs. This reduces the number of fasteners in multiple fastenings and maximises safety. As part of the DuoLine, the DuoTec consists of two plastic components. The red and hard component of the plug's sleeve enables the uniform distribution of the load, while the grey and white prevent damage to the surface of the board during fastening and thus a load reduction. In applications in board materials, which have a hollow space behind them, the DuoTec is applied as a tumbling plug. In solid building materials, the plug can also be used as a spreader plug. Applications Suspended kitchen cabinets Wall cabinets Bookshelves Wardrobes Handrails Paintings Mirrors Lamps Heavy hanging baskets Building materials Suitable for: Plasterboard Gypsum fibreboard Wooden panels (e.g. OSB, chipboard, MDF, etc.) Steel plate Plastic sheets Concrete hollow brick Also suitable for: Solid materials such as concrete and wood ds: dsc: Scope of delivery (per purchase of 5) 2x DuoTec hollow wall plug 2x screw 5x 60 kts: Hollow wall plug DuoTec 10 S with screw (2 pcs) kpn: 537263 kpn_dash: kpn_clear: 537263 bkpn: FISCHER 537263 bkpn_clear: FISCHER 537263 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 537263 sr_ns: FISCHER537263
r: 02615256 p: 2.6 pid: 176192 b: FISCHER q: 0 st: lt: 15 ean: 4006209809259 sr: FISCHER 80925 sr_no_br: 80925 sr_no_br_cl: 80925 sr_cl: FISCHER80925 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter 12 Length 90 n: FISCHER 80925 scaffolding eye GS 12 x 90 cn: EYE SCREW cn2: EYE SCREW cn_clear: EYESCREW d: Product description The standard scaffold anchoring. The fischer eye bolt GS made of zinc-plated steel is, together with the fischer expansion plug S 14 ROE, suitable for fixing into concrete and solid brick. The screw-in markings provide a visual control during assembly and prevent the eye from being unintentionally broken off. The fischer eye bolt is ideally suited for fixing façade scaffolds, cables, or chains. The eye does not open due to the high-quality weld Optimum interaction between eyebolt and fischer expansion plug The ideal interaction of the scaffold eye screw and plug allows for a high load-bearing capacity, thus providing increased safety The high-quality weld stops the eye from opening The large diameter of the cover caps (available separately) covers drill holes completely and discreetly, even those with slightly broken edges Suitable for In order to achieve the maximum load-bearing capacity, nylon plugs should only be used once In perforated brick and aerated concrete, we recommend combination with the plug S 16 H R The screw-in markings provide a visual control during assembly, and thus allow for a simple and problem-free installation Pre-drill into wood when not using plugs. The drill bit diameter should correspond to the core diameter of the screw Suitable cover caps AD 12x40 for closing off residual drill holes for S 14 ROE Not suitable for swings, hammocks etc Building materials GS 12 + S 14 ROE suitable for: Concrete Solid sand-lime brick Natural stone with dense structure Solid brick Solid brick made from lightweight concrete GS 12 + S 16 H R suitable for: Vertically perforated brick Perforated sand-lime brick Aerated concrete Application Façade scaffolds Ropes Chains Trellises Lighting Clothes lines Hanging baskets ds: dsc: kts: scaffolding eye GS 12 x 90 kpn: 80925 kpn_dash: kpn_clear: 80925 bkpn: FISCHER 80925 bkpn_clear: FISCHER 80925 c_path: Home / Fasteners and machine components / Fasteners / Screws / Eye screw | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer screws / Fischer eye screw sr_no_br_cl_ns: 80925 sr_ns: FISCHER80925
r: 08096862 p: 2.58 pid: 176232 b: FISCHER q: 0 st: lt: 8 ean: 4048962462340 sr: FISCHER 564609 sr_no_br: 564609 sr_no_br_cl: 564609 sr_cl: FISCHER564609 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 8 mm Effective length 10 mm Overall length 75 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread designation M8 n: FISCHER 564609 piercing anchor FAZ II Plus 8/10 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: piercing anchor FAZ II Plus 8/10 R stainless steel kpn: 564609 kpn_dash: kpn_clear: 564609 bkpn: FISCHER 564609 bkpn_clear: FISCHER 564609 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564609 sr_ns: FISCHER564609
r: 87050187 p: 2.53 pid: 176366 b: FISCHER q: 0 st: lt: 8 ean: 4006209502594 sr: FISCHER 50259 sr_no_br: 50259 sr_no_br_cl: 50259 sr_cl: FISCHER50259 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Length 190 mm n: FISCHER 50259 anchor rod RG M16 x 190 electrolytically zinc-plated 5.8 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The proven rod anchor for internal use with a mortar cartridge or injection mortar. The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5. 8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas. Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge Zinc-galvanised steel for internal use The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety Please refer to the approvals for the resin capsules and mortar used Suitable for Due to its oblique edge, the anchor rod RG M is particularly suitable for use in conjunction with resin capsules The anchor rod RG M is set using a hammer drill and the accompanying setting tool in rotating and hitting motions During setting, the oblique edge of the RG M destroys the capsule, and mixes and activates the mortar Use with injection mortar is also possible. Here, the anchor rod is manually inserted into the drill hole with a light rotating movement until it reaches the base of the hole Building materials In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete In connection with several fischer injection mortars approved or suitable for different building materials Application Anchorings with resin capsule RSB and RSB mini Anchorings with resin capsule RM II Anchorings with each of the fischer injection mortars FIS SB, FIS EM, FIS EB II, FIS V, FIS VL, FIS V Zero, FIS P Plus, FIS P, FIS EP and FIS Green ds: dsc: kts: anchor rod RG M16 x 190 electrolytically zinc-plated 5.8 kpn: 50259 kpn_dash: kpn_clear: 50259 bkpn: FISCHER 50259 bkpn_clear: FISCHER 50259 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 50259 sr_ns: FISCHER50259
