r: 02019857 p: 0.68 pid: 15986 b: FISCHER q: 0 st: lt: 8 ean: 4006209441268 sr: FISCHER 44126 sr_no_br: 44126 sr_no_br_cl: 44126 sr_cl: FISCHER44126 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 54 mm Drilling diameter 6 mm n: FISCHER 44126 nail anchor FNA II 6x25 H with hook electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor with hook for multiple fixings. The fischer nail anchor FNA II 6 with hook is made of zinc-plated steel. The FNA II is set in a time-saving manner in the pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with hook is suitable for fixing air lines and hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold With hook The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and push-through installation. The FNA II OE and H are suitable for pre-positioned installation The installed FNA II nail anchor expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x25 H with hook electrolytically galvanised kpn: 44126 kpn_dash: kpn_clear: 44126 bkpn: FISCHER 44126 bkpn_clear: FISCHER 44126 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44126 sr_ns: FISCHER44126
r: 02671106 p: 0.65 pid: 15439 b: FISCHER q: 0 st: lt: 6 ean: 4006209886786 sr: FISCHER 88678 sr_no_br: 88678 sr_no_br_cl: 88678 sr_cl: FISCHER88678 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm With screw Yes Drilling diameter 10 mm Application General type (screw head) PZ3 Wall plug type Hammer-in plug Material (wall plug) Polyamide (Nylon®) Drill hole depth - mm Length (Wall plug) 182 mm n: FISCHER 88678 frame plug F 10 M 152 electrolytically galvanised steel cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The screw fixing with countersunk head for the stress-free installation of window and door frames. The fischer metal frame fixing F-M is a special plug for the stress-free, lasting stand-off installation of window and door frames and of squared timbers. It consists of a metal sleeve and a zinc-plated steel screw. The F-M is set in a time-saving push-through installation. When the screw is tightened, the cone is pulled into the plug sleeve and expands against the wall of the drill hole. This ensures a fixation that is free from tensile force and pressure, thus guaranteeing a secure hold in solid and hollow building materials. The F-M is tested for fire resistance class R120, and offers safety for fire-protection-relevant applications. The F-M metal frame plug achieves fire resistance R 120. This allows for use in areas where fire resistance is relevant The operating principle prevents the window frame from being pulled against the substrate, and ensures a stress-free and long-lasting fixing of the frame The special plug geometry anchors the metal and plastic profiles against compressive and tensile loads, and allows for a secure hold of the window frame The cover caps (available separately) can be used to discreetly cover the screw heads Suitable for The F-M is suitable for push-through installation By tightening the screw, the cone is drawn into the sleeve and the fixing is expanded which wedges it inside the drill hole. The window frames are thus fixed in a stress-free manner The maximum installation torque is 5 Nm Building materials Concrete Vertically perforated brick Hollow blocks made from lightweight concrete Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid brick made from lightweight concrete Solid brick Application Window frames Door frames Squared timbers ds: dsc: kts: frame plug F 10 M 152 electrolytically galvanised steel kpn: 88678 kpn_dash: kpn_clear: 88678 bkpn: FISCHER 88678 bkpn_clear: FISCHER 88678 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 88678 sr_ns: FISCHER88678
r: 02019164 p: 0.65 pid: 10564 b: FISCHER q: 0 st: lt: 8 ean: 4006209685044 sr: FISCHER 68504 sr_no_br: 68504 sr_no_br_cl: 68504 sr_cl: FISCHER68504 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 8 mm Overall length 94 mm Material Steel Surface treatment Zinc plated Safety anchor No Drilling diameter 10 mm n: FISCHER FSA 10x80/35 B sleeve anchor with nut electrolytically zinc plated - 68504 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The through bolt anchor with nut and washer for structural fixings in non-cracked concrete. The fischer sleeve anchor FSA-B is a zinc-plated steel anchor with nut and washer for structural fixings made of zinc-plated steel. The FSA-B is set in the time-saving through-type installation. When tightening, the cone is pulled into the expansion sleeve and expands it against the hole wall. The recesses act as a crumple zone to take the torque slippage. The fixture is therefore pulled towards the anchoring base. The fischer sleeve anchor FSA-B is ideal for fastening fixings that are not relevant in safety terms such as ladders, gates, and temporary fixings in non-cracked concrete. Simple alignment due to optimised anchor geometry, even in narrow spaces Surface flush removal due to detachable screw connection With nut and washer The optimised geometry minimises setting energy and enables the use in extremely narrow spaces. This allows for user-friendly installation The anchor design makes it possible to use different head shapes for flexible design solutions: Hexagon head (type S), bolt version with nut and washer (type B) The detachable screw connection allows for surface flush removal Suitable for The FSA is suitable for push-through installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall The half-moon shaped recesses act as a crumple zone to take the torque slippage, so that the attachment is pulled onto the anchor base Building materials Suitable for: Concrete C12/15 to C20/25, non-cracked Natural stone with dense structure Application Handrails Consoles Ladders Cable trays Gates Façades Temporary or structural fixings ds: dsc: kts: sleeve anchor with nut electrolytically zinc plated kpn: FSA 10x80/35 B kpn_dash: kpn_clear: FSA10x8035B bkpn: FISCHER FSA 10x80/35 B bkpn_clear: FISCHER FSA10x8035B c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 68504 sr_ns: FISCHER68504
r: 02359625 p: 0.64 pid: 176188 b: FISCHER q: 0 st: lt: 6 ean: 4048962013535 sr: FISCHER 502456 sr_no_br: 502456 sr_no_br_cl: 502456 sr_cl: FISCHER502456 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm Length (Wall plug) 52 mm Drill hole depth - mm Material (wall plug) Polyamide (Nylon®) Wall plug type Hammer-in plug With screw Yes Application General type (screw head) T40; HEX 13 mm Drilling diameter 10 mm n: FISCHER 502456 construction plug SXR 10 x 52 FUS hexagon head cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The efficient with short expansion element The fischer frame fixing SXR-FUS is a plug made of high-quality nylon along with the fischer hexagonal screw and moulded washer. Due to the special plug geometry, the SXR can be used in solid and hollow building materials. Due to the low anchorage depth of only 50 mm, the frame fixing can be handled in an especially cost-effective manner for multiple fixing of non-load-bearing systems. The fischer frame fixing SXR-FUS is particularly recommended with the hexagonal screw and moulded washer for fixing metal constructions. Low anchorage depth saves time and costs ETA approval in concrete and masonry With safety screw with hexagonal head and moulded washer Plug expands in solid building materials The plug anchors itself in the cavity in perforated building materials The special functioning allows for use in solid and hollow building materials with an anchorage depth of just 50 mm, ensuring an economical fixing The ETA assessment covers use in a range of solid and hollow building materials, and guarantees a secure fixing The specially developed combination of plugs and screws ensures the very best handling. The plug has a noticeable hold, making installation more convenient The extensive range offers the right plug for every fixing Suitable for The SXR is suitable for push-through installation The SXR expands in solid building materials In hollow building materials the loads are transferred in the area of the block fillets With vertically perforated bricks, only use rotary drilling (no impact drilling) Countersunk head screws are recommended for fixing timber constructions. For metal constructions, plug with wide sleeve rim and hexagon head screws with moulded washer Building materials Approved for: Concrete >= C12/15 Vertically perforated brick Hollow blocks made from lightweight concrete Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid block made from lightweight and normal weight concrete Solid brick Thermal insulation blocks Also suitable for: Natural stone with dense structure Solid panel made from gypsum Application Façade, ceiling and roof substructures made of wood and metal Windows Gates and doors Wardrobes Kitchen hanging cabinets Squared timbers Beams TV consoles Wall covering Metal brackets Metal supports Cable ducts Cable trays ds: dsc: kts: construction plug SXR 10 x 52 FUS hexagon head kpn: 502456 kpn_dash: kpn_clear: 502456 bkpn: FISCHER 502456 bkpn_clear: FISCHER 502456 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 502456 sr_ns: FISCHER502456
r: 87051106 p: 0.64 pid: 74119 b: FISCHER q: 0 st: lt: 1 ean: 4006209407004 sr: FISCHER 40700 sr_no_br: 40700 sr_no_br_cl: 40700 sr_cl: FISCHER40700 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 8 mm Effective length 30/40 mm Overall length 91 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M8 n: FISCHER 40700 rapid-action anchor FBN II 8/30 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 8/30 electrolytically galvanised steel kpn: 40700 kpn_dash: kpn_clear: 40700 bkpn: FISCHER 40700 bkpn_clear: FISCHER 40700 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40700 sr_ns: FISCHER40700
r: 02907516 p: 0.63 pid: 176078 b: FISCHER q: 0 st: lt: 15 ean: 4048962265248 sr: FISCHER 538663 sr_no_br: 538663 sr_no_br_cl: 538663 sr_cl: FISCHER538663 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Hole diameter 8,5 mm n: FISCHER 538663 clamping plate HK 31 8.5 cn: CLAMPING PLATE cn2: CLAMPING PLATE cn_clear: CLAMPINGPLATE d: Product description Connector - Channel washer HK 31 The fischer connector channel washer HK 31 has special retaining lugs that make it easier to achieve a strong, positive-fit connection, even in the case of suspended channels. The retaining lugs enable easy installation longitudinally and transverse to the mounting channel profile FLS. fischer offers the channel washer with standard 8. 5 mm and 10. 5 mm perforations. These allow an easy and precise installation process and thus save time and money. The galvanised zinc version is suitable for installation in buildings. The fire protection certificate provides added safety in the case of the channel washer. Channel washre for stable direct mounting of FLS channels to the substrate or for rigid attachment of pipe clamps to FLS rails using FSM Clix Form-fit connection with the FLS channel due to laterally curved contours Application-specific corrosion protection through galvanisation For use in dry interior areas Fire protection test R120 MLAR R30 sample cable system test The special retaining brackets at the SV connecting elements enable a form-locking installation longitudinal and transverse to the channel direction to adapt the channel connection effectively The standardised slots of the Channel washer enable an exact push-through connection of FLS mounting channels easy and fast Application The Channel washer HK 31 is used for stable connections and to strengthen the FLS profile for a fixing to the substrate For use in dry interior areas ds: dsc: kts: clamping plate HK 31 8.5 kpn: 538663 kpn_dash: kpn_clear: 538663 bkpn: FISCHER 538663 bkpn_clear: FISCHER 538663 c_path: Home / Fasteners and machine components / Fasteners / Rails and mounting / Clamping plate | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer rails and mounting / Fischer clamping plate sr_no_br_cl_ns: 538663 sr_ns: FISCHER538663
r: 02907517 p: 0.63 pid: 176119 b: FISCHER q: 0 st: lt: 15 ean: 4048962265255 sr: FISCHER 538664 sr_no_br: 538664 sr_no_br_cl: 538664 sr_cl: FISCHER538664 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Hole diameter 10,5 mm n: FISCHER 538664 clamping plate HK 31 10.5 cn: CLAMPING PLATE cn2: CLAMPING PLATE cn_clear: CLAMPINGPLATE d: Product description Connector - Channel washer HK 31 The fischer connector channel washer HK 31 has special retaining lugs that make it easier to achieve a strong, positive-fit connection, even in the case of suspended channels. The retaining lugs enable easy installation longitudinally and transverse to the mounting channel profile FLS. fischer offers the channel washer with standard 8. 5 mm and 10. 5 mm perforations. These allow an easy and precise installation process and thus save time and money. The galvanised zinc version is suitable for installation in buildings. The fire protection certificate provides added safety in the case of the channel washer. Channel washre for stable direct mounting of FLS channels to the substrate or for rigid attachment of pipe clamps to FLS rails using FSM Clix Form-fit connection with the FLS channel due to laterally curved contours Application-specific corrosion protection through galvanisation For use in dry interior areas Fire protection test R120 MLAR R30 sample cable system test The special retaining brackets at the SV connecting elements enable a form-locking installation longitudinal and transverse to the channel direction to adapt the channel connection effectively The standardised slots of the Channel washer enable an exact push-through connection of FLS mounting channels easy and fast Application The Channel washer HK 31 is used for stable connections and to strengthen the FLS profile for a fixing to the substrate For use in dry interior areas ds: dsc: kts: clamping plate HK 31 10.5 kpn: 538664 kpn_dash: kpn_clear: 538664 bkpn: FISCHER 538664 bkpn_clear: FISCHER 538664 c_path: Home / Fasteners and machine components / Fasteners / Rails and mounting / Clamping plate | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer rails and mounting / Fischer clamping plate sr_no_br_cl_ns: 538664 sr_ns: FISCHER538664
r: 87051105 p: 0.61 pid: 74420 b: FISCHER q: 0 st: lt: 4 ean: 4006209406694 sr: FISCHER 40669 sr_no_br: 40669 sr_no_br_cl: 40669 sr_cl: FISCHER40669 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 8 mm Effective length 20/30 mm Overall length 81 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M8 n: FISCHER 40669 rapid-action anchor FBN II 8/20 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 8/20 electrolytically galvanised steel kpn: 40669 kpn_dash: kpn_clear: 40669 bkpn: FISCHER 40669 bkpn_clear: FISCHER 40669 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40669 sr_ns: FISCHER40669
r: 02671094 p: 0.61 pid: 15436 b: FISCHER q: 0 st: lt: 14 ean: 4006209886625 sr: FISCHER 88662 sr_no_br: 88662 sr_no_br_cl: 88662 sr_cl: FISCHER88662 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm With screw Yes Drilling diameter 8 mm Application General type (screw head) PZ2 Wall plug type Hammer-in plug Material (wall plug) Polyamide (Nylon®) Drill hole depth - mm Length (Wall plug) 92 mm n: FISCHER 88662 frame plug F 8 M 92 electrolytically galvanised steel cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The screw fixing with lenticular flange head for the stress-free installation of window and door frames. The fischer metal frame fixing F-M is a special plug for the stress-free, lasting stand-off installation of window and door frames and of squared timbers. It consists of a metal sleeve and a zinc-plated steel screw. The F-M is set in a time-saving push-through installation. When the screw is tightened, the cone is pulled into the plug sleeve and expands against the wall of the drill hole. This ensures a fixation that is free from tensile force and pressure, thus guaranteeing a secure hold in solid and hollow building materials. The F-M is tested for fire resistance class R120, and offers safety for fire-protection-relevant applications. The F-M metal frame plug achieves fire resistance R 120. This allows for use in areas where fire resistance is relevant The operating principle prevents the window frame from being pulled against the substrate, and ensures a stress-free and long-lasting fixing of the frame The special plug geometry anchors the metal and plastic profiles against compressive and tensile loads, and allows for a secure hold of the window frame The cover caps (available separately) can be used to discreetly cover the screw heads Suitable for The F-M is suitable for push-through installation By tightening the screw, the cone is drawn into the sleeve and the fixing is expanded which wedges it inside the drill hole. The window frames are thus fixed in a stress-free manner The maximum installation torque is 5 Nm Building materials Concrete Vertically perforated brick Hollow blocks made from lightweight concrete Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid brick made from lightweight concrete Solid brick Application Window frames Door frames Squared timbers ds: dsc: kts: frame plug F 8 M 92 electrolytically galvanised steel kpn: 88662 kpn_dash: kpn_clear: 88662 bkpn: FISCHER 88662 bkpn_clear: FISCHER 88662 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 88662 sr_ns: FISCHER88662
r: 02019771 p: 0.59 pid: 15977 b: FISCHER q: 0 st: lt: 8 ean: 4006209460221 sr: FISCHER 46022 sr_no_br: 46022 sr_no_br_cl: 46022 sr_cl: FISCHER46022 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 10 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M8 n: FISCHER 46022 nail anchor FNA II 6x30/10 M6 nut electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The installation-friendly Hammerset anchor with thread and flange nut for multiple fixings. The fischer nail anchor FNA II 6 with thread and flange nut is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through or pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II with thread and flange nut is suitable for fixing metal clamps for conduits and pipes in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Easy removal of fire protection board without damage Reusability of fire protection board Safe anchorage, particularly when exposed to vibration, wind, and pushing/pulling influences Low anchoring depth (30 mm) Convenient installation without torque-controlled setting tool Approved system that has proven itself one million times over Suitable for The washer significantly increases the pulling forces and, at the same time, prevents the damage of the panel during removal Removal by means of easy pinching off of nail head thanks to special 2-stage pliers For fast installation, use the compressed air setting device (item no. 093731) Building materials Concrete C12/15 to C50/60, cracked and non-cracked For multi-point fixings of non-load-bearing systems Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30/10 M6 nut electrolytically galvanised steel kpn: 46022 kpn_dash: kpn_clear: 46022 bkpn: FISCHER 46022 bkpn_clear: FISCHER 46022 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 46022 sr_ns: FISCHER46022
r: 02019758 p: 0.58 pid: 95638 b: FISCHER q: 0 st: lt: 8 ean: 4006209441091 sr: FISCHER 44109 sr_no_br: 44109 sr_no_br_cl: 44109 sr_cl: FISCHER44109 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 5 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M6 n: FISCHER 44109 nail anchor FNA II 6x30 M6/5 with nut electrolytically zinc plated cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The installation-friendly Hammerset anchor with thread and flange nut for multiple fixings. The fischer nail anchor FNA II 6 with thread and flange nut is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through or pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II with thread and flange nut is suitable for fixing metal clamps for conduits and pipes in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Easy removal of fire protection board without damage Reusability of fire protection board Safe anchorage, particularly when exposed to vibration, wind, and pushing/pulling influences Low anchoring depth (30 mm) Convenient installation without torque-controlled setting tool Approved system that has proven itself one million times over Suitable for The washer significantly increases the pulling forces and, at the same time, prevents the damage of the panel during removal Removal by means of easy pinching off of nail head thanks to special 2-stage pliers For fast installation, use the compressed air setting device (item no. 093731) Building materials Concrete C12/15 to C50/60, cracked and non-cracked For multi-point fixings of non-load-bearing systems Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30 M6/5 with nut electrolytically zinc plated kpn: 44109 kpn_dash: kpn_clear: 44109 bkpn: FISCHER 44109 bkpn_clear: FISCHER 44109 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 44109 sr_ns: FISCHER44109
r: 08096869 p: 0.58 pid: 176237 b: FISCHER q: 0 st: lt: 8 ean: 4048962461978 sr: FISCHER 564572 sr_no_br: 564572 sr_no_br_cl: 564572 sr_cl: FISCHER564572 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 10 mm Overall length 65 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread dimension M6 n: FISCHER 564572 Piercing anchor FAZ II Plus 6/10 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, now with even higher tensile strengths. Heavy loads can be secured in cracked concrete using the steel anchor. The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity. For example, the steel anchor is ideal for the anchoring of railings, cable trays, and consoles. Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Millimeter accurate adjustment to the loads due to the variable anchoring depths The first bolt anchor M6 with ETA evaluation option 1: for safe approved anchorages The tried-and-tested expansion clip ensures highest load capacity even with size M6 Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 6/10 EV electrolytically galvanised steel kpn: 564572 kpn_dash: kpn_clear: 564572 bkpn: FISCHER 564572 bkpn_clear: FISCHER 564572 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564572 sr_ns: FISCHER564572
r: 02063032 p: 0.57 pid: 176198 b: FISCHER q: 0 st: lt: 5 ean: 4048962070255 sr: FISCHER 505528 sr_no_br: 505528 sr_no_br_cl: 505528 sr_cl: FISCHER505528 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 30 mm Overall length 75 mm Thread dimension M6 n: FISCHER 505528 rapid-action anchor FBN II 6/30 electrolytically galvanised cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete. The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas. Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility Simple assembly due to few taps and minimal slippage The drive-in pin protects the thread from damage. This saves time during installation and removal The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 6/30 electrolytically galvanised kpn: 505528 kpn_dash: kpn_clear: 505528 bkpn: FISCHER 505528 bkpn_clear: FISCHER 505528 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 505528 sr_ns: FISCHER505528
r: 02890415 p: 0.57 pid: 176026 b: FISCHER q: 0 st: lt: 10 ean: 4048962180749 sr: FISCHER 522698 sr_no_br: 522698 sr_no_br_cl: 522698 sr_cl: FISCHER522698 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm With screw Yes Drilling diameter 10 mm Application General type (screw head) T40 Wall plug type Hammer-in plug Material (wall plug) Polyamide (Nylon®) Drill hole depth 90 mm Length (Wall plug) 80 mm n: FISCHER 522698 construction plug SXRL 10 x 80 T countersunk head cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The versatile with multiple anchorage depth The fischer frame fixing SXRL-T is approved along with the fischer countersunk head screw with TX40 drive for multiple fixings of non-load-bearing systems in masonry, concrete, and aerated concrete. The two expansion zones in the fixing induce forces equally into perforated masonry, these combine to form a long expansion element in aerated concrete and solid building material. The frame fixing with the safety screw made out of zinc-plated steel is suitable for fixings in internal areas such as windows, coat racks, wall cupboards, or TV consoles. ETA assessment with excellent load values: Safe multiple fixings of non-structural systems in concrete and masonry The long expansion element with two anchorage depths makes the SXRL versatile Loads are applied evenly to the building material thanks to the fixing geometry. This means that the fillets are not destroyed in the case of thin-walled building materials Simple to assemble: Ribs prevent plug rotation during installation The long expansion element with multiple anchorage depths of 50, 70 and 90 mm for SXRL 8 and SXRL 10 and 70 and 90 mm for SXRL 14 makes the SXRL an extremely versatile product Through the special geometry of the plug, the retention forces are evenly distributed in the drill hole The approval for single-point fixing in cracked concrete makes the SXRL the designated specialist in concrete particularly for tasks such as the installation of awning roofs and outdoor railings compared to steel anchors When it is to be set deep, the longer ribs prevent the plug from turning during installation The SXRL 14 is additionally approved for applications that are subject to pressure and may be used for façade structures that are installed without wall bracket with a spacing The SXRL with effective lengths up to 290 mm provides the right plug for every application Suitable for The SXRL is suitable for push-through installation In perforated brick masonry a force transmission that protects the substrate is guaranteed through the two expansion zones. The porous block fillets are not crushed by the second expansion zone an therefore serves to transmit the force In aerated concrete and solid building materials, the two expansion zones combine to form one long expansion element, thus providing for a uniform and flat distribution of the load into the substrate Countersunk head screws are recommended for fixing timber constructions. For metal constructions, plug with wide sleeve rim and hexagon head screws with moulded washer Building materials Approved for: Vertically perforated brick Aerated concrete Hollow blocks made from lightweight concrete Perforated sand-lime brick Thermal insulation blocks Solid block made from lightweight and normal weight concrete Solid brick Solid sand-lime brick Concrete >= C12/15 Also suitable for: Natural stone with dense structure Solid panel made from gypsum Application Façade, ceiling and roof substructures made of wood and metal Facade substructures under compression load (e. g. distance installation without a wall bracket) Windows Gates and doors Wardrobes Kitchen hanging cabinets Squared timbers Beams TV consoles Wall covering Metal brackets Metal supports Cable ducts Cable trays ds: dsc: kts: construction plug SXRL 10 x 80 T countersunk head kpn: 522698 kpn_dash: kpn_clear: 522698 bkpn: FISCHER 522698 bkpn_clear: FISCHER 522698 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 522698 sr_ns: FISCHER522698
r: 02285269 p: 0.57 pid: 14180 b: FISCHER q: 0 st: lt: 8 ean: 4006209886762 sr: FISCHER 88676 sr_no_br: 88676 sr_no_br_cl: 88676 sr_cl: FISCHER88676 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm With screw Yes Drilling diameter 10 mm Application General type (screw head) PZ3 Wall plug type Hammer-in plug Material (wall plug) Polyamide (Nylon®) Drill hole depth 150 mm Length (Wall plug) 132 mm n: FISCHER 88676 frame plug F 10 M 132 electrolytically galvanised steel cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The screw fixing with countersunk head for the stress-free installation of window and door frames. The fischer metal frame fixing F-M is a special plug for the stress-free, lasting stand-off installation of window and door frames and of squared timbers. It consists of a metal sleeve and a zinc-plated steel screw. The F-M is set in a time-saving push-through installation. When the screw is tightened, the cone is pulled into the plug sleeve and expands against the wall of the drill hole. This ensures a fixation that is free from tensile force and pressure, thus guaranteeing a secure hold in solid and hollow building materials. The F-M is tested for fire resistance class R120, and offers safety for fire-protection-relevant applications. The F-M metal frame plug achieves fire resistance R 120. This allows for use in areas where fire resistance is relevant The operating principle prevents the window frame from being pulled against the substrate, and ensures a stress-free and long-lasting fixing of the frame The special plug geometry anchors the metal and plastic profiles against compressive and tensile loads, and allows for a secure hold of the window frame The cover caps (available separately) can be used to discreetly cover the screw heads Suitable for The F-M is suitable for push-through installation By tightening the screw, the cone is drawn into the sleeve and the fixing is expanded which wedges it inside the drill hole. The window frames are thus fixed in a stress-free manner The maximum installation torque is 5 Nm Building materials Concrete Vertically perforated brick Hollow blocks made from lightweight concrete Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid brick made from lightweight concrete Solid brick Application Window frames Door frames Squared timbers ds: dsc: kts: frame plug F 10 M 132 electrolytically galvanised steel kpn: 88676 kpn_dash: kpn_clear: 88676 bkpn: FISCHER 88676 bkpn_clear: FISCHER 88676 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 88676 sr_ns: FISCHER88676
r: 02315650 p: 0.56 pid: 176183 b: FISCHER q: 0 st: lt: 8 ean: 4006209906712 sr: FISCHER 90671 sr_no_br: 90671 sr_no_br_cl: 90671 sr_cl: FISCHER90671 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: n: FISCHER 90671 centring sleeve PBZ for M8, M10 and M12 cn: CENTERING SLEEVE cn2: CENTERING SLEEVE cn_clear: CENTERINGSLEEVE d: Product description Installation aid for centring the anchor rods and internal thread anchors. The fischer centring sleeve PBZ is an aid for centring anchor rods FIS A M8-M12 and FIS E M6 / M8 for fixing in aerated concrete with a conical drill hole. Facilitates the precise alignment of the fixing element and the overhead installations The centring sleeve PBZ fixes the anchor in the drill hole, thus also allowing for overhead installation Suitable for The centring sleeve PBZ is placed into the drill hole Afterwards, the drill hole is filled with injection mortar from the drill hole mouth and the anchor rod is set The centring sleeve PBZ fixes the anchor rod in the drill hole Building materials Aerated concrete Application Anchorage in aerated concrete with injection mortars FIS V, FIS VS LOW SPEED, FIS VW HIGH SPEED ds: dsc: kts: centring sleeve PBZ for M8, M10 and M12 kpn: 90671 kpn_dash: kpn_clear: 90671 bkpn: FISCHER 90671 bkpn_clear: FISCHER 90671 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Centering sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer centering sleeve sr_no_br_cl_ns: 90671 sr_ns: FISCHER90671
r: 02019161 p: 0.55 pid: 10556 b: FISCHER q: 0 st: lt: 8 ean: 4006209685020 sr: FISCHER 68502 sr_no_br: 68502 sr_no_br_cl: 68502 sr_cl: FISCHER68502 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 6 mm Overall length 115 mm Material Steel Surface treatment Zinc plated Safety anchor No Drilling diameter 8 mm n: FISCHER FSA 8x105/65 B sleeve anchor with nut electrolytically zinc plated - 68502 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The through bolt anchor with nut and washer for structural fixings in non-cracked concrete. The fischer sleeve anchor FSA-B is a zinc-plated steel anchor with nut and washer for structural fixings made of zinc-plated steel. The FSA-B is set in the time-saving through-type installation. When tightening, the cone is pulled into the expansion sleeve and expands it against the hole wall. The recesses act as a crumple zone to take the torque slippage. The fixture is therefore pulled towards the anchoring base. The fischer sleeve anchor FSA-B is ideal for fastening fixings that are not relevant in safety terms such as ladders, gates, and temporary fixings in non-cracked concrete. Simple alignment due to optimised anchor geometry, even in narrow spaces Surface flush removal due to detachable screw connection With nut and washer The optimised geometry minimises setting energy and enables the use in extremely narrow spaces. This allows for user-friendly installation The anchor design makes it possible to use different head shapes for flexible design solutions: Hexagon head (type S), bolt version with nut and washer (type B) The detachable screw connection allows for surface flush removal Suitable for The FSA is suitable for push-through installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall The half-moon shaped recesses act as a crumple zone to take the torque slippage, so that the attachment is pulled onto the anchor base Building materials Suitable for: Concrete C12/15 to C20/25, non-cracked Natural stone with dense structure Application Handrails Consoles Ladders Cable trays Gates Façades Temporary or structural fixings ds: dsc: kts: sleeve anchor with nut electrolytically zinc plated kpn: FSA 8x105/65 B kpn_dash: kpn_clear: FSA8x10565B bkpn: FISCHER FSA 8x105/65 B bkpn_clear: FISCHER FSA8x10565B c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 68502 sr_ns: FISCHER68502
r: 02019755 p: 0.55 pid: 16126 b: FISCHER q: 0 st: lt: 8 ean: 4006209441114 sr: FISCHER 44111 sr_no_br: 44111 sr_no_br_cl: 44111 sr_cl: FISCHER44111 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Effective length 5 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M6 n: FISCHER 44111 nail anchor FNA II 6x25 M6/5 with nut electrolytically zinc plated cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The installation-friendly Hammerset anchor with thread and flange nut for multiple fixings. The fischer nail anchor FNA II 6 with thread and flange nut is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through or pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II with thread and flange nut is suitable for fixing metal clamps for conduits and pipes in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Easy removal of fire protection board without damage Reusability of fire protection board Safe anchorage, particularly when exposed to vibration, wind, and pushing/pulling influences Low anchoring depth (30 mm) Convenient installation without torque-controlled setting tool Approved system that has proven itself one million times over Suitable for The washer significantly increases the pulling forces and, at the same time, prevents the damage of the panel during removal Removal by means of easy pinching off of nail head thanks to special 2-stage pliers For fast installation, use the compressed air setting device (item no. 093731) Building materials Concrete C12/15 to C50/60, cracked and non-cracked For multi-point fixings of non-load-bearing systems Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x25 M6/5 with nut electrolytically zinc plated kpn: 44111 kpn_dash: kpn_clear: 44111 bkpn: FISCHER 44111 bkpn_clear: FISCHER 44111 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 44111 sr_ns: FISCHER44111
r: 87990392 p: 0.54 pid: 76435 b: FISCHER q: 0 st: lt: 6 ean: 4006209886748 sr: FISCHER 88674 sr_no_br: 88674 sr_no_br_cl: 88674 sr_cl: FISCHER88674 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Diameter (wall plug) - mm With screw Yes Drilling diameter 10 mm Application General type (screw head) PZ3 Wall plug type Hammer-in plug Material (wall plug) Polyamide (Nylon®) Drill hole depth - mm Length (Wall plug) 112 mm n: FISCHER 88674 frame plug F 10 M 112 electrolytically galvanised steel cn: WALL PLUG cn2: WALL PLUG cn_clear: WALLPLUG d: Product description The screw fixing with countersunk head for the stress-free installation of window and door frames. The fischer metal frame fixing F-M is a special plug for the stress-free, lasting stand-off installation of window and door frames and of squared timbers. It consists of a metal sleeve and a zinc-plated steel screw. The F-M is set in a time-saving push-through installation. When the screw is tightened, the cone is pulled into the plug sleeve and expands against the wall of the drill hole. This ensures a fixation that is free from tensile force and pressure, thus guaranteeing a secure hold in solid and hollow building materials. The F-M is tested for fire resistance class R120, and offers safety for fire-protection-relevant applications. The F-M metal frame plug achieves fire resistance R 120. This allows for use in areas where fire resistance is relevant The operating principle prevents the window frame from being pulled against the substrate, and ensures a stress-free and long-lasting fixing of the frame The special plug geometry anchors the metal and plastic profiles against compressive and tensile loads, and allows for a secure hold of the window frame The cover caps (available separately) can be used to discreetly cover the screw heads Suitable for The F-M is suitable for push-through installation By tightening the screw, the cone is drawn into the sleeve and the fixing is expanded which wedges it inside the drill hole. The window frames are thus fixed in a stress-free manner The maximum installation torque is 5 Nm Building materials Concrete Vertically perforated brick Hollow blocks made from lightweight concrete Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid brick made from lightweight concrete Solid brick Application Window frames Door frames Squared timbers ds: dsc: kts: frame plug F 10 M 112 electrolytically galvanised steel kpn: 88674 kpn_dash: kpn_clear: 88674 bkpn: FISCHER 88674 bkpn_clear: FISCHER 88674 c_path: Home / Fasteners and machine components / Fasteners / Plugs and covers / Wall plug | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer plugs and covers / Fischer wall plug sr_no_br_cl_ns: 88674 sr_ns: FISCHER88674
r: 02019784 p: 0.54 pid: 17419 b: FISCHER q: 0 st: lt: 8 ean: 4006209441152 sr: FISCHER 44115 sr_no_br: 44115 sr_no_br_cl: 44115 sr_cl: FISCHER44115 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 40 mm Effective length 5 mm Head diameter 13 mm Drilling diameter 6 mm n: FISCHER 44115 nail anchor FNA II 6x30/5 with nail head electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor for multiple fixings. The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Series installation possible with setting tool for the hammer drill. This saves time and costs The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and Hare suitable for pre-positioned installation The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and nonious hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30/5 with nail head electrolytically galvanised kpn: 44115 kpn_dash: kpn_clear: 44115 bkpn: FISCHER 44115 bkpn_clear: FISCHER 44115 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44115 sr_ns: FISCHER44115
